Pacific Sun Kore 7th Скачать руководство пользователя

Страница: 45 / 79

Page 45

Kore 7th Manual / kHLab Edition

5.7. ATO / Temp config

DC pump

group box

Refill time (in seconds)

Time in seconds defining how long the DC pump will

work when water low level sensor is activated. After

four unsuccessful attempts the pump will be turned

off (to prevent damage). It’s highly advised to select

„Unsuccessful water refill Alarm check-box so you can

be notified upon failure.

Manual turn on/off

Allows selecting the flow rate manually (flow adjust in

40-100% range).

Short beep after proper refill

Enabling this option will cause a beep after each refill

of water.

Sound alarm

Turn on/off sound alarm when high level sensor is

activated.

Choose alarm type

Allows you to select sound signal generated by the

doser.

Test alarm

Test sound alarm

Reset ATO alarm

Allows resetting the ATO after four unsuccessful refills.

Temperature

group box

Reset High/Low temp

Erase highest/lowest temperature record from doser

memory.

Temperature alarm

Turn on/off sound alarm for temperature settings

Содержание Kore 7th
















































































Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды

Pacific Sun Kore 7th, Руководство пользователя

Результаты поиска

Содержание Kore 7th

Отзывы:

Похожие инструкции для Kore 7th

Бренды по названию

Популярные бренды