Pacific Scientific 6430 Скачать руководство пользователя

Страница: 32 / 60

Table cont’d

Input/Output

Pin

Explanation

DIR -

J12-7

Input that determines the direction of motor

rotation. If standard motor wiring is followed, the

motor will turn clockwise if the opto current is zero.

The sense of the DIR + input can be reversed by

reversing the connection of either (but not both)

motor phase connectors (i.e. switching A & A OR B

& B). Refer to the figure at the end of the table for

timing and circuit information.

ENABLE -

J12-8

Input used to enable or disable the 6430’s power

stage. With the J6 5-6 jumper out (factory default)

the power stage is enabled if the opto current is

zero and disabled if the opto is driven. Inserting the

jumper reverses this functionality. See figure at the

end of the table for circuit information. There is a

delay of approximately 500

s after enabling the

drive and the power stage becoming active.

Enabled

Emitter

J12-9

Output. Emitter of transistor that is on when the

6430’s power stage is active. See figure at the end

of the table for timing and circuit information.

Typical interface

The figure on the following page shows a typical interface

between the user’s electronics and the 6430. The TTL gates

should have totem pole outputs and be capable of sinking at

least 10.0 mA at 0.4 volts.

6430 Installation and Hardware Reference Manual - Rev 1

2 - 19

Installation

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6430





























































Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды

Pacific Scientific 6430, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды