Pacific Scientific 6430 Скачать руководство пользователя

Страница: 16 / 60

2.3 Selecting Other System Components

Selecting an

indexer

The 6430 drive requires STEP and DIRECTION inputs.

Select an indexer that provides, as a minimum, these

commands. A compatible indexer will provide the capability to

drive the input circuits shown in Section 2.5.4. For most

applications that operate at speeds above 300 RPM, an indexer

that can ramp the step frequency is required.

Selecting a

motor

The 6430 is designed for use with Pacific Scientific’s line of

hybrid stepper motors or most other 2 phase stepper motors.

The drive works with either the standard line or the enhanced

high performance line of stepper motors. The motor winding

current rating must be compatible with the output current of

the drive package.
Refer to the Torque/Speed Curves in the Pacific Scientific

“Motion Control Solutions Catalog” or contact your local

Pacific Scientific distributor for sizing and motor compatibility

assistance.

2.4 Mounting the 6430 Unit

Mounting

guidelines

Your installation should meet the following guidelines:

•

Vertical orientation for the unit.

•

Flat, solid surface capable of supporting the approximate

6.0 lbs. weight (2.7 kg. mass) of the unit.

•

Free of excessive vibration or shock.

•

Minimum unobstructed space of 4 inches (10 cm) above

and below the unit.

•

Maximum ambient temperature of 50

6430 Installation and Hardware Reference Manual - Rev 1

2 - 3

Installation

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6430





























































Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды

Pacific Scientific 6430, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды