Pacific Scientific 6430 Скачать руководство пользователя

Страница: 47 / 60

4.2.2 Troubleshooting the drive board

Corrective action

table

Use the following table to troubleshoot the drive board:

SYMPTOM

CORRECTIVE ACTION

Motor produces

no torque,

Meter reads

high.

Note: See figure

on next page.

Ensure that the J6 5-6 jumper is out, or if in, that the enable

input opto is driven with at least 3 mA.

Disconnect the AC power. Disconnect motor cable and cycle

the J1 power supply Off and On. If the meter reads low, check

motor cable and motor for shorts across the windings or

between the windings and the motor case.

Motor produces

no torque,

meter reads low.

Note: See figure

on next page.

Verify that DIP Switch S1 position 6, 7, and 8 (current select)

are set correctly.

Re-check that the motor cable is wired correctly and properly

plugged into the drive.

Motor produces

torque but does

not turn.

Make sure that the STEP input is switching and meets specified

electrical and timing requirements.

Motor rotates in

the wrong

direction

Check polarity of the DIRECTION input. Also, check that the

DIRECTION input satisfies the specified electrical and timing

requirements.

Reverse the A and A motor phases.

Motor does not

reach expected

position

Check that the step size setting of the drive is the same as the

step size setting of the indexer.

Verify that the motor does not stall. If it does:

1. Use a finer step size to avoid low-speed resonance problems.

2. Enable Digital Electronic Damping control. (S1 position 4

OFF).

Check that the STEP and DIRECTION Inputs satisfy all

electrical and timing requirements.

4 - 4

6430 Installation and Hardware Reference Manual - Rev 1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6430





























































Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды

Pacific Scientific 6430, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды