Pacific Scientific 6430 Скачать руководство пользователя страница 10

Страница: 10 / 60

User

adjustments

Motor current - sets the motor phase current to 5.0, 4.375,

3.75, 3.125, 2.5, 1.875, 1.25, or 0.625 A rms.

using DIP

switch S1

Step size - sets the amount of shaft rotation per step (with the

decimal jumper installed). The settings are full, half, 1/5, 1/10,

1/25, 1/50, 1/125, and 1/250 steps per (micro)step. This

corresponds to 200, 400, 1000, 2000, 5000, 10,000, 25,000, and

50,000 (micro) steps per revolution with a standard 1.8° motor.

With the decimal jumper removed, the settings are 1/2, 1/4,

1/8, 1/16, 1/32, 1/64, 1/128, and 1/256 steps per (micro) step.

This corresponds to 400, 800, 1600, 3200, 6400, 12,800, 25,600,

and 51,200 (micro) steps per revolution.
Digital Electronic Damping control - enables this patented

feature which eliminates loss of torque and possible motor

stalling conditions when operating at mid-range speeds. This

instability is a phenomenon of the electronic, magnetic and

mechanical characteristics of a stepping motor system. The

compensation circuit damps mid-range oscillations by

advancing or delaying switching of the output current relative

to the incoming pulse train.
Idle current reduction (ICR) - enables or disables idle current

reduction which reduces motor winding current by 50% of its

rated value during motor dwell periods. ICR begins 0.1

second after the last input step pulse occurs. This delay can

also be set to 0.05 seconds or 1 second using a plug-on jumper.
Note: The current will return to 100% at the next step pulse.

using plug-on

jumpers

Step filter - when enabled (jumper installed) rejects noise

pulses on step input less than 500

s wide. Useful if maximum

step rate is 500 KHz.
Enable sense - allows the polarity of the enable input to be

reversed. With the jumper installed, the enable input

opto-isolator must be driven to enable drive. With the jumper

removed, enable input opto-isolator must be driven to disable.

using AC Switch

SW1

Off line 120/240 Vac - switch selects AC input. DO NOT apply

240 Vac with AC Switch in 120 Vac position.

6430 Installation & Hardware Reference Manual - Rev 1

1 - 3

Overview

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6430





























































Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды

Pacific Scientific 6430, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание 6430

Отзывы:

Похожие инструкции для 6430

Бренды по названию

Популярные бренды