PACIFIC CYCLE Part Скачать руководство пользователя | Manualshive

Страница: 67 / 119

background image

60

Attaching Training Wheel Brace to Bicycle

There are two different braces used to attach the training
wheels to the bicycle: the C-Shape Brace and the Flat Brace.
Determine which brace was included with your bicycle and fol-
low the given instructions for that particular brace.

C-Shape Brace

Remove the axle nut and washer from the rear wheel axle.
Place the brace stabilizer washer onto the axle and align the
washer so that the notch on the washer fits into the rear frame
drop out.  Next, place the C-shaped wheel brace onto the axle
and replace the washer and axle nut.  Tighten the axle nut
securely, making sure that the wheel brace stays in the proper
vertical position.  The elongated hole on the wheel brace
allows the training wheel height to be adjusted for proper fit.

Flat Brace

Remove the axle nut and washer from the rear wheel axle.
Place the flat wheel brace onto the axle.  Next place the brace
stabilizer washer onto the axle and align it so that the notch
fits into the rear frame drop out.  Replace the washer and axle
nut.  Tighten the axle nut securely, making sure that the wheel
brace stays in the proper vertical position.  The elongated
hole on the wheel brace allows the training wheel height to be
adjusted for proper fit.

C-Shape

Flat

«
...
65
66
67
68
69
...
»

Содержание Part
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Part

Бренд: Panasonic Страницы: 443

Бренд: Samsung Страницы: 2

Wireless Temperature/Humidity Station

Бренд: DAVIS Страницы: 8

Бренд: FeiYu Tech Страницы: 6

Бренд: Faudi Страницы: 18

Бренд: Harbor Freight Tools Страницы: 4

Бренд: T-Home Страницы: 52

Бренд: Xerox Страницы: 2

Бренд: DigiTech Страницы: 15

Бренд: Doug Thorley Headers Страницы: 5

Nils Extreme MTW03

Бренд: Abisal Страницы: 21

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: PCB Piezotronics Страницы: 9

Бренд: Hach Страницы: 52

Бренд: Element14 Страницы: 32

Бренд: Gitzo Страницы: 1

Бренд: GE Страницы: 12

Бренд: Sandel Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды