PACIFIC CYCLE Part Скачать руководство пользователя | Manualshive

Страница: 85 / 119

background image

78

Some brakes have a quick release mechanism to allow easier wheel removal. Whenever you adjust the brakes,
make sure the quick release mechanism is in the closed position.

Never ride unless the quick release is firmly locked in the closed position.

Lubrication

The brake lever and brake caliper pivot points should be oiled with
2-3 drops of light oil at least every three months to ensure smooth
operation and to reduce wear. Cables should be greased along
their entire length, after removing them from their casings, at least
every six months. Always grease new cables before fitting.

Adjustment - Sidepull Calipers

Minor brake adjustment can be made via the cable adjusting bar-
rel, usually located at the upper cable arm. To adjust, squeeze
the brake pads against the rim, loosen the lock nut and turn the
adjuster Brake pad clearance should be a maximum 2mm from
the rim. When correct, re-tighten the lock nut. If the pads cannot
be set close enough to the rim in this manner, you may have to
adjust the cable length. Screw the barrel adjuster 3/4 of the way in,
squeeze the pads against the rim, undo the cable anchor bolt and
pull the cable through with pliers. Re-tighten the cable anchor bolt
and apply full force to the brake lever to test, then fine tune using
the barrel adjuster. If one pad is closer to the rim than the other,
loosen the fixing nut at the back of the brake, apply the brake to
hold it centered, and re-tighten the fixing nut.

Brake Lever

Brake Lever Housing

Cable Adjusting Barrel

Lock nut

Cable Adjusting Barrel

Center Bolt

Brake Shoe

Side-Pull Brakes

Fixing Nut

in Back

Cable

Anchor

Bolt

Ensure the Brake fixing nut is secured tightly.
Failure to do this may cause the Brake assembly
to dislodge from the fork.

«
...
83
84
85
86
87
...
»

Содержание Part
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Part

Бренд: Iget Страницы: 7

Бренд: Eaton Страницы: 21

Бренд: AC Schnitzer Страницы: 16

Бренд: CAB Страницы: 21

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Naterial Страницы: 40

Бренд: Takara Belmont Страницы: 36

Бренд: Van Air Systems Страницы: 8

Dual Shock Rally Master

Бренд: Trust Страницы: 9

Бренд: Manfrotto Страницы: 36

Бренд: Baumer Страницы: 3

X-ACT CONTOUR 53491

Бренд: HUSKY LINERS Страницы: 2

Бренд: Cargo Floor Страницы: 16

Бренд: eufy Security Страницы: 12

Drive Pro EZ Build 41130

Бренд: Meyer Страницы: 11

Бренд: White Outdoor Страницы: 4

Бренд: Hudora Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды