PACIFIC CYCLE Part Скачать руководство пользователя

Страница: 107 / 119

100

CAUTION:

If you can fully close the quick release without wrapping your fingers around the fork blade for

leverage, and the lever does not leave a clear imprint in the palm of your hand, the tension is insufficient.

Open the lever; turn the tension adjusting nut clockwise a quarter turn; then try again.

(5) If the lever cannot be pushed all the way to a position parallel to the fork blade, return the lever to the

OPEN

position. Then turn the tension adjusting nut counterclockwise one-quarter turn and try tightening

the lever again.

(6) Close the brake shoes; then spin the wheel to make sure that it is centered in the frame and clears

the brake shoes.

WARNING:

Secondary retention devices are not a substitute for correct quick release adjustment. Failure

to properly adjust the quick release mechanism can cause the wheel to wobble or disengage, which could

cause you to lose control and fall, resulting in serious injury or death.

c. Removing a Quick Release Rear Wheel

(1) Shift the rear derailleur to high gear (the smallest, outermost rear sprocket).

(2) Open up the brake shoes.

(3) Pull the derailleur body back with your right hand.

(4) Rotate the quick-release lever to the

OPEN

position.

(5) Lift the rear wheel off the ground a few inches and, with the derailleur still pulled back, push the wheel

forward and down until it comes out of the rear dropouts.

d. Installing a Quick Release Rear Wheel

(1) Shift the rear derailleur to its outermost position

(2) Pull the derailleur body back with your right hand.

(3) Rotate the quick-release lever to the

OPEN

position. The lever should be on the side of the wheel

opposite the derailleur and freewheel sprockets.

(4) Put the chain on top of the smallest free wheel sprocket. Then, insert the wheel into the frame

dropouts and pull it all the way in to the dropouts.

(5) Tighten the adjusting nut until it is finger tight against the frame dropout; then rotate the lever toward

the front of the bike until it is parallel to the frame’s chainstay or seatstay and is curved toward the wheel.

CAUTION:

If you can fully close the quick release without wrapping your fingers around the fork blade for

leverage, and the lever does not leave a clear imprint in the palm of your hand, the tension is insufficient.

Open the lever; turn the tension adjusting nut clockwise a quarter turn; then try again.

(6) If the lever cannot be pushed all the way to a position parallel to the chainstay or seatstay tube, return

the lever to the

OPEN

position. Then turn the adjusting nut counterclockwise one-quarter turn and try

tightening again.

Содержание Part
























































































































Результаты поиска

Содержание Part

Отзывы:

Похожие инструкции для Part

Бренды по названию

Популярные бренды

PACIFIC CYCLE Part, Инструкция по эксплуатации

Результаты поиска

Содержание Part

Отзывы:

Похожие инструкции для Part

Бренды по названию

Популярные бренды