PACIFIC CYCLE Part Скачать руководство пользователя | Manualshive

Страница: 30 / 119

background image

23

NOTE:

Comfort Series (CS) bicycles may be equipped with a stem that has an adjustable angle.

In addition to the normal assembly, these stems will require angling the stem to the desired position,
and securely tightening the 6mm angle bolt located in front of the stem bolt.

Failure to do this may cause loss of steering control.

Tightening/Preloading Aheadset

Stem Installation (Should be assembled on the
bike already)

  1. Insert the compression bolt through the top
     cap and the stem.  Begin threading into the
     star nut.
  2.Tighten compression bolt so it removes all
    play from the fork, but allows the fork to rotate
    smoothly.
  3. Align the stem with the front wheel.  Tighten
    the stem clamp bolts to secure the stem to the
    steerer tube.

Handlebar Installation

  1. Remove the stem cap bolts and stem cap.
  2. Insert handlebar into the stem cap.
  3. Tighten the stem cap bolts equally.  Note
    the distance between the stem and stem cap:
    It should be equal on the top and bottom of the
    stem cap.

A

must be equal distance.

Installed

by

factory

Compression Bolt

Top Cap

Stem Clamp Bolts

Spacer

Headset Wedge

Bearing Race

Bearing Dust Cover

Bearing Retainer

Star Nut

(Inside Steerer Tube)

Upper Headset Cup

Headtube

Lower Headset Cup

Bearing Retainer

Bearing Dust Cover

Headset Crown Race

fork

Steerer

T

ube

Handlebar

Stem Cap

Bolts

Stem Cap

«
...
28
29
30
31
32
...
»

Содержание Part
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Part

Бренд: Canon Страницы: 115

Бренд: FEIYUTECH Страницы: 8

Бренд: FeiYu Tech Страницы: 2

Бренд: FeiYu Tech Страницы: 2

Бренд: FEIYUTECH Страницы: 26

Бренд: ICON Страницы: 8

Бренд: iDataLink Страницы: 30

Q.HOME+ ESS HYB G2

Бренд: Qcells Страницы: 2

Бренд: UniFlow Страницы: 42

Бренд: Carax Страницы: 2

Бренд: Manfrotto Страницы: 36

Бренд: Baumer Страницы: 3

X-ACT CONTOUR 53491

Бренд: HUSKY LINERS Страницы: 2

KARLSUDD TRAVEL BED

Бренд: Carena Страницы: 8

Бренд: Home Accents Holiday Страницы: 2

Бренд: Metra Electronics Страницы: 4

REARSIGHT OnStar 250-8822

Бренд: Rostra Страницы: 2

Бренд: Calex Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды