Pace Sodrtek ST 145 Скачать руководство пользователя | Manualshive

Страница: 22 / 22

background image

PACE Incorporated retains the right to make changes to specifications contained herein at any time,
without notice. Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest
specifications.

The following are trademarks and/or service marks of PACE, Incorporated, MD, USA:

INSTACAL

™

, FUMEFLO

™

, HEATWISE

™

, PACEWORLDWIDE

™

, PERMAGROUND

™

,

POWERPORT

™

, POWERMODULE

™

, TEMPWISE

™

, TIP-BRITE

™

, AUTO-OFF

™

,

and

TEKLINK

™

.

The following are registered trademarks and/or service marks of PACE Incorporated, Annapolis Junction
Maryland U.S.A.

ARM-EVAC

®

, FLO-D-SODR

®

, MINIWAVE

®

, PACE

®

, SENSATEMP

®

, SNAP-VAC

®

,

SODRTEK

®

, SODR-X-TRACTOR

®

, THERMOFLO

®

, THERMOJET

®

, THERMOTWEEZ

®

,

VISIFILTER

®

, THERMO-DRIVE

®

, and TOOLNET

®

.

PACE products meet or exceed all applicable military and civilian EOS/ESD, temperature stability and
other specifications including MIL STD 2000, ANSI/JSTD 001, IPC7711, and IPC A-610.

www.paceworldwide.com

PACE USA

PACE Europe

9030 Junction Drive

Sherbourne House

Annapolis Junction, MD 20701

Sherbourne Drive

USA

Tilbrook, Milton Keynes

MK7

8HX

United

Kingdom

Tel:

(301) 490-9860

(44) 01908-277666

Fax: (301) 498-3252

(44) 01908-277777

©2004 PACE Inc., Annapolis Junction, Maryland

Page 22 of 22

All Rights Reserved

«
...
20
21
22

Содержание Sodrtek ST 145























Отзывы:

Нет отзывов

Похожие инструкции для Sodrtek ST 145

Бренд: Zehnder Rittling Страницы: 36

Бренд: Walabot Страницы: 9

Бренд: i-onik Страницы: 59

Бренд: Zeck Audio Страницы: 16

Бренд: ADEMCO Страницы: 56

Бренд: ECO Schulte Страницы: 18

Бренд: K.M.E. Страницы: 40

Бренд: Daikin Страницы: 9

Бренд: Aiwa Страницы: 76

Бренд: WG Страницы: 32

Бренд: iCONNECT Страницы: 20

Бренд: Air Liquide Страницы: 23

Бренд: ANDELI Страницы: 23

Бренд: Zepro Страницы: 68

Бренд: STAMOS Страницы: 7

JBL On Tour Plus

Бренд: JBL Страницы: 2

Audio Everywhere

Бренд: Listen Technologies Страницы: 2

Бренд: On-Hold Plus Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды