manualshive.com logo in svg

Pace Sodrtek ST 145, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Pace Sodrtek ST 145 Скачать руководство пользователя страница 18

Corrective Maintenance 
 

Power Source 

 

Refer to the table below.  Most malfunctions are simple and easy to correct.    
 

Symptom 

 

Probable Cause 

 

Solution 

 

No power to system.  

Blown Fuse  

Check handpiece using "Heater Assembly 
Checkout Procedures" in the respective 
handpiece manual. Replace the fuse (located 
in the AC Receptacle Fuse Holder) with one 
of the same rated value. 
 

 

Power Source Malfunction 

Contact the PACE Service Department for 
assistance. 

Handpiece air hose has a kink 
or a hole in the hose. 

Check handpiece hose. Replace air hose if 
necessary  

VisiFilter or handpiece filter 
clogged.  

Replace VisiFilter or handpiece filter.  

Handpiece chamber not 
seated properly in handpiece.  

Check handpiece. Reseat chamber if 
necessary.  

Insufficient vacuum or 
air pressure. Motor 
Pump runs.  

Defective Motor Pump 
Assembly.  

Check vacuum and air pressure at Motor 
Pump Assembly air hose connections. 
Replace Motor Pump Assembly if necessary.  

Defective handpiece.  

Check handpiece using "Heater Assembly 
Checkout Procedures", in the respective 
handpiece manual. 

Defective Motor Pump 
Assembly.  

Check for 12 VDC at motor terminals with 
handpiece switch actuated. Replace Motor 
Pump Assembly if defective.  

No vacuum or air 
pressure. Motor Pump 
does not run.  

Defective Main PCB Assembly  If there is no 12 VDC at Motor Pump 

Assembly, repair or replace Main PCB 
Assembly. 

Defective Handpiece Heater 

Check handpiece using "Heater Assembly 
Checkout Procedures" in the respective 
handpiece manual. 

Handpiece will not 
heat 

Power Source Malfunction 

Contact the PACE Service Department for 
assistance. 

  
 

Handpieces 

 

Please refer to the specific handpiece manual for the “Heater Assembly Checkout Procedures.” 
 

 

©2004 PACE Inc., Annapolis Junction, Maryland 

Page 18 of 22 

All Rights Reserved 

Содержание Sodrtek ST 145























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды