Ozito X PXC PXGMTK-4182 Скачать руководство пользователя страница 3

Страница: 3 / 40

GENERAL POWER TOOL SAFETY WARNINGS

5. Battery tool use and care

Recharge only with the charger specified by the manufacturer.

A charger that is suitable for one type of battery pack may

create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs.

Use of any other battery packs may create a risk of injury and

fire.

When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other

small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d. U

nder abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally seek medical help

. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modified.

Damaged or modified batteries may exhibit unpredictable

behaviour resulting in fire, explosion or risk of injury.

Do not expose a battery pack or tool to fire or excessive temperature.

Exposure to fire or temperature above 130°C may

cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the

instructions.

Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk

of fire.

6. Service

Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the

safety of the power tool is maintained.

Never service damaged battery packs.

Service of battery packs should only be performed by the manufacturer or authorized

service provider.

Содержание X PXC PXGMTK-4182









































Результаты поиска

Содержание X PXC PXGMTK-4182

Отзывы:

Похожие инструкции для X PXC PXGMTK-4182

Бренды по названию

Популярные бренды

Ozito X PXC PXGMTK-4182, Инструкция по эксплуатации

Результаты поиска

Содержание X PXC PXGMTK-4182

Отзывы:

Похожие инструкции для X PXC PXGMTK-4182

Бренды по названию

Популярные бренды