Ozito X PXC PXGMTK-4182 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

background image

Tooth cutting direction.

a

b

a

b

b

15

WARNING!

IF YOU TRY TO ROTATE THE

CHAIN TENSIONING SCREW (b) WHILST
THE CHAIN SPROCKET COVER BOLT IS

TIGHT, IT WILL RESULT IN THE CHAIN NOT
LOOSENING AND POSSIBLE DAMAGE TO THE
CHAIN TENSIONING SCREW AND THE CHAIN
TENSIONING PIN.

2. Adjust the chain tension with the multi-tool 13/4mm. Turning CLOCKWISE increases the chain

tension, turning it COUNTER-CLOCKWISE decreases the

chain tension.

For the correct chain tension, firmly pull up on the chain at the

middle of the top of the exposed guide bar. When the chain

is pulled up to its highest point, the bottom tip of the links

should only just stay in the track [middle of the guide bar].

3. Once the correct tension has been achieved, tighten the

chain sprocket cover bolt to lock the chain bar in place.

Note:

Chains lengthen slightly as the link pins set into place.

They set into place from the load applied to the chain, this

process continues throughout the life of all chains as they

gradually wear from use.

Tensioning the Chain

1. Using supplied multi-tool 13/4mm loosen the chain

sprocket cover bolt. Do not remove chain sprocket cover.

5. Re-mount and finger-tighten the chain sprocket cover with

the chain sprocket cover bolt.

Note:

Only tighten the chain sprocket cover bolt securely

once the chain tension has been adjusted (see:

Tensioning

the chain

.)

«
...
13
14
15
16
17
...
»

Содержание X PXC PXGMTK-4182









































Отзывы:

Нет отзывов

Похожие инструкции для X PXC PXGMTK-4182

Бренд: Fein Страницы: 70

Бренд: Keithley Страницы: 160

Бренд: Keithley Страницы: 22

Бренд: Keithley Страницы: 66

Бренд: Keithley Страницы: 58

Бренд: tacwise Страницы: 5

Бренд: YATO Страницы: 112

Бренд: Surtek Страницы: 8

Бренд: Hama Страницы: 2

Бренд: Varan Страницы: 11

Бренд: Yost Vises Страницы: 6

Бренд: LUMBERJACK TOOLS Страницы: 2

Бренд: Mengual Страницы: 68

eFlow102N Series

Бренд: EFLOW Страницы: 16

Бренд: PairGain Страницы: 21

ROCK DOG ROUTER

Бренд: weha Страницы: 7

Бренд: Mr. Blacksmith Страницы: 20

Бренд: Parkside Страницы: 163

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды