background image

5

d) remove any adjusting key or wrench before turning the power tool on.

 A 

wrench or a key left attached to a rotating part of the power tool may result in 

personal injury.

e) do not overreach. Keep proper footing and balance at all times. 

This enables 

better control of the power tool in unexpected situations.

f)  dress properly. do not wear loose clothing or jewellery. Keep your hair,  

clothing and gloves away from moving parts. 

Loose clothes, jewellery or long 

hair can be caught in moving parts.

g) if devices are provided for the connection of dust extraction and collection 

facilities, ensure these are connected and properly used. 

Use of dust collection 

can reduce dust-related hazards.

4) power tool use and care
a) do not force the power tool. use the correct power tool for your application. 

The correct power tool will do the job better and safer at the rate for which it   

was designed.

 

b) do not use the power tool if the switch does not turn it on and off. 

Any power 

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) disconnect the plug from the power source and/or the battery pack from the 

power tool before making any adjustments, changing accessories, or  

 

storing power tools. 

Such preventive safety measures reduce the risk of starting 

the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons 

unfamiliar with the power tool or these instructions to operate the power 
tool. 

Power tools are dangerous in the hands of untrained users.

e) maintain power tools. check for misalignment or binding of moving parts, 

breakage of parts and any other condition that may affect the power tool’s 
operation. if damaged, have the power tool repaired before use. 

Many    

accidents are caused by poorly maintained power tools.

f)  Keep cutting tools sharp and clean. 

Properly maintained cutting tools with sharp 

cutting edges are less likely to bind and are easier to control.

g) use the power tool, accessories and tool bits etc. in accordance with these 

instructions, taking into account the working conditions and the work to be 
performed. 

Use of the power tool for operations different from those intended 

could result in a hazardous situation.

5) Service
a) Have your power tool serviced by a qualified repair person using only  

identical replacement parts. 

This will ensure that the safety of the power tool  

is maintained.

 

b) if the supply cord is damaged, it must be replaced by the manufacturer, 

its 

service agent or similarly qualified persons in order to avoid a hazard.

General poWer tool Safety WarninGS

Содержание SSB-405

























Отзывы: