OWL FO-4B Скачать руководство пользователя страница 26

Страница: 26 / 77

Press

to complete the Link Wizard.

Press

to begin taking readings.

TAKE READINGS

If testing only one wavelength, then skip to the next step.

If testing at two wavelengths, press

to set the Fiber OWL 4 into AUTO mode, then press and hold

on the

WaveSource until the multimode port indicator LED starts flashing, then immediately release the button. The WaveSource
will begin to alternate between

and

, and after a few seconds, readings for both wavelengths will appear on the

Fiber OWL 4 display.

Disconnect the mandrel-wrapped patch cable from the Fiber OWL 4 and take the units to opposite ends of the link.

Connect the units to the first fiber to test as shown in Figure 6. Your readings will vary from the example below.

Once the STORE option becomes active, press

to store the data point. If this is the first fiber in the link, you may be

prompted to enter a new label.

Press

to save the data point(s).

Disconnect the patch cables from the patch panels and move them to the next port in the patch panel, then repeat steps

through

until all fibers in the link have been tested.

green

red

Do NOT disconnect the patch cable(s) from the light source at any time until all fibers have been tested.

AUTO

QUICK REFERENCE GUIDES

PAGE 5 OF 5

1 2 3 4 5 6 7 8 9 10 11 12

FIGURE 6

Equipment

Connection for

Optical Loss

Measurements

LIGHT SOURCE CONNECTOR

PORT NOTES:

– CONNECTOR TYPE MAY VARY
– DO NOT INSERT ANGLED

PHYSICAL CONTACT (APC)
CONNECTOR

UNITS

FIBER

FBR:1

_____________________

STORE

LINK #1

68%

WAVE

850nm

PASS

2 85

Optical Power Meter:

Fiber OWL 4

Fiber Optic Light Source:

WAVESOURCE Series Multimode Sources

Содержание FO-4B














































































Результаты поиска

Содержание FO-4B

Отзывы:

Похожие инструкции для FO-4B

Бренды по названию

Популярные бренды

OWL FO-4B, Руководство по эксплуатации

Результаты поиска

Содержание FO-4B

Отзывы:

Похожие инструкции для FO-4B

Бренды по названию

Популярные бренды