OWL FO-4B Скачать руководство пользователя страница 21

Страница: 21 / 77

TAKE READINGS

Disconnect the mandrel-wrapped patch cable from the Fiber OWL 4 and take the units to opposite ends of the link.

Connect the units to the first fiber to test as shown in Figure 6. Your readings will vary from the example below.

Press

to store the data point. If this is the first data point in the link, you may be prompted to enter a new label.

Press

to save the data point.

Disconnect the patch cables from the patch panels and move them to the next port in the patch panel, then repeat steps

through

until all fibers in the link have been tested at 850nm.

If also testing at 1300nm, repeat steps

through

, but this time use the mandrel-wrapped patch cable attached to

the 1300nm port. Also, make sure that you set the Fiber OWL 4 and the Dual OWL to 1300nm.

Do NOT disconnect the patch cable(s) from the light source at any time until all fibers have been tested.

QUICK REFERENCE GUIDES

PAGE 6 OF 6

1 2 3 4 5 6 7 8 9 10 11 12

FIGURE 6

Equipment

Connection for

Optical Loss

Measurements

LIGHT SOURCE CONNECTOR

PORT NOTES:

– CONNECTOR TYPE MAY VARY
– DO NOT INSERT ANGLED

PHYSICAL CONTACT (APC)
CONNECTOR

UNITS

FIBER

FBR:1

_____________________

STORE

LINK #1

68%

WAVE

850nm

PASS

2 85

Optical Power Meter:

Fiber OWL 4

Fiber Optic Light Source:

DUAL OWL Series Multimode Sources

Содержание FO-4B














































































Результаты поиска

Содержание FO-4B

Отзывы:

Похожие инструкции для FO-4B

Бренды по названию

Популярные бренды

OWL FO-4B, Руководство по эксплуатации

Результаты поиска

Содержание FO-4B

Отзывы:

Похожие инструкции для FO-4B

Бренды по названию

Популярные бренды