Oval ALTI mass CA001 Скачать руководство пользователя страница 66

Страница: 66 / 162

L--740--28--E

8. OPERATION

8.1 Flushing the Piping Assembly

If scale and sludge are expected to be left in the piping assembly, particularly in a new piping assembly,

flush the assembly prior to sensor unit installation.

8.2 Confirming the Sensor Unit for Correct Installation

For safety,s sake, confirm connecting bolts to tightness and gaskets for condition. Make certain of flow

direction at the same time.

8.3 Leak Check

Fill the sensor tube completely with process fluid and check for any leak from connections.

8.4 Supplying the Power

Upon completion of checks for correct wiring connections, supply power. The LCD will show the following

information:

8.5 Measurement Line Startup

By starting up the pump, opening valves, etc., carefully allow the process fluid to flow.

8.6 Warm-up

To ensure stability of the measuring conditions of equipment, provide about 20 minutes, warmup period.

(A message "WARMUP 20" stays on after startup. The number shows remaining time (min).)

8.7 Zeroing Procedure

On seeing that the measuring conditions have come to an equilibrium, shut off the downstream valve

completely. Make a zeroing adjustment under these conditions (see the topic under 9.8 Zeroing).

8.8 Readying for Operation

Now preparation for operation is complete. Initiate measurement.

Corporate logo is shown.

Self diagnostics begins.

If nothing unusual is found, "OK" appears at right of

each item, bringing up the next window.

(If NG appears, running a check on that item is

required.

See 9.6.3 Transmitter Check, correct the condition, and

turn on power again.)

Variable view and measurement begins.

Содержание ALTI mass CA001



































































































































































Результаты поиска

Содержание ALTI mass CA001

Отзывы:

Похожие инструкции для ALTI mass CA001

Бренды по названию

Популярные бренды

Oval ALTI mass CA001, Инструкция по эксплуатации

Результаты поиска

Содержание ALTI mass CA001

Отзывы:

Похожие инструкции для ALTI mass CA001

Бренды по названию

Популярные бренды