Outback Power Systems GS3548E Скачать руководство пользователя страница 66

Страница: 66 / 76

Specifications

900-0145-01-01 Rev A

Table 12

Electrical Specifications for Radian Models

Specification

GS7048E

GS3548E

DC Input Maximum Current (surge)

406.5 Adc

203.3 Adc

DC Input Maximum Current (short-circuit)

8975 Adc

4488 Adc

Battery Charger Maximum AC Input

30 Aac at 230 Vac

15 Aac at 230 Vac

Battery Charger Maximum DC Output

100 Adc

50 adc

DC Output Voltage Range (charging)

44 to 68 Vdc

Auxiliary Output

0.7 Adc at 12 Vdc

Auxiliary Relay

10 A at 250 Vac or 30 Vdc

Mechanical Specifications

Table 13

Mechanical Specifications for Radian Models

Specification

GS7048E

GS3548E

Inverter Dimensions (H x W x D)

71.1 x 40.6 x 22.2 cm

(28 x 16 x 8.75")

71.1 x 40.6 x 22.2 cm

(28 x 16 x 8.75")

Shipping Dimensions (H x W x L)

36.8 x 53.3 x 87.6 cm

(14.5 x 21 x 34.5")

36.8 x 53.3 x 87.6 cm

(14.5 x 21 x 34.5")

Inverter Weight

56.8 kg (125 lb)

37.2 kg (82 lb)

Shipping Weight

63.5 kg (140 lb)

42.6 kg (94 lb)

Accessory Ports

RJ11 (batt temp) and

RJ45 (remote)

RJ11 (batt temp) and

RJ45 (remote)

Non-volatile Memory

Yes

Neutral-Ground Bond Switching

Chassis Type

Vented

Environmental Specifications

Table 14

Environmental Specifications for Radian Models

Specification

Value

Rated Temperature Range (meets component specifications; however, please note

that the inverter output wattage is derated above 25°C)

–20°C to 50°C ( –4°F to 122°F)

Operational Temperature Range (functions, but does not necessarily meet all
component specifications)

–40°C to 60°C (–40°F to 140°F)

Storage Temperature Range

–40°C to 60°C (–40°F to 140°F)

IP (Ingress Protection) Rating of Enclosure

IP20

Environmental Category

Indoor unconditioned

Wet Locations Classification

Wet locations: No

Relative Humidity Rating

93%

Pollution Degree Classification

PD 2

Maximum Altitude Rating

2000 m (6561’)

Overvoltage Category (AC Input)

Overvoltage Category (DC Input)

Содержание GS3548E













































































Результаты поиска

Содержание GS3548E

Отзывы:

Бренды по названию

Популярные бренды

Outback Power Systems GS3548E, Руководство оператора

Результаты поиска

Содержание GS3548E

Отзывы:

Бренды по названию

Популярные бренды