Outback Power Systems GS3548E Скачать руководство пользователя

Страница: 65 / 76

900-0145-01-01 Rev A

Specifications

Electrical Specifications

NOTE

: Items qualified with “default” can be manually changed using the system display.

Table 12

Electrical Specifications for Radian Models

Specification

GS7048E

GS3548E

Continuous Output Power at 25°C

7000 VA

3500 VA

Continuous AC Output Current at 25°C

30.4 Aac

15.2 Aac

AC Output Voltage (nominal)

230 Vac

AC Output Frequency (default)

50 Hz

AC Output Type

Single-phase

AC Waveform

True Sinewave

Efficiency (typical)

92%

Total Harmonic Distortion (maximum)

< 5%

Harmonic Distortion (maximum single voltage)

< 2%

AC Output Voltage Regulation

± 2%

Appliance Protective Class (IEC)

Class I

Power Factor

–1 to 1

Inrush Current

None

AC Maximum Output Current (1 ms peak)

100 Aac

50 Aac

AC Maximum Output Current (100 ms RMS)

70.7 Aac

35.35 Aac

AC Overload Capability (100 ms surge)

16.3 kVA

8.15 kVA

AC Overload Capability (5 second)

11.5 kVA

5.75 kVA

AC Overload Capability (30 minute)

7.9 kVA

3.95 kVA

AC Maximum Output Fault Current and Duration

109 Aac for 0.364 seconds

54.5 Aac for 0.364 seconds

Power Consumption (idle) – Invert mode, no load

34 watts

Power Consumption (idle) – Search mode

10 watts

Power Consumption – Off

4 watts

AC Input Voltage Range

170 to 290 Vac

AC Input Frequency Range (default)

45 to 55 Hz

AC Input Current (maximum continuous)

50 Aac

Grid-Interactive Voltage Range (default)

208 to 252 Vac

Grid-Interactive Frequency Range (default)

47 to 51 Hz

DC Input Voltage (nominal)

48 Vdc

DC Input Voltage Range

40 to 64 Vdc

DC Maximum Input Voltage

68 Vdc

DC Input Power (continuous)

7.634 kVA

3.817 kVA

DC Input Maximum Current (continuous full power)

175 Adc

87.5 Adc

Содержание GS3548E













































































Результаты поиска

Содержание GS3548E

Отзывы:

Похожие инструкции для GS3548E

Бренды по названию

Популярные бренды

Outback Power Systems GS3548E, Руководство оператора

Результаты поиска

Содержание GS3548E

Отзывы:

Похожие инструкции для GS3548E

Бренды по названию

Популярные бренды