Ossila T2005 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 27

background image

LED Measurement System

User Manual

11

Ossila Limited © 2022

8.

Installation

1.

Install the Ossila LED IVL software on your PC.

I.

Run the file ‘Ossila

-LED-IVL-Installer-X-X-X-

X.exe’ on the USB memory stick

provided.

II.

Follow the on-screen instructions to install the software.

2.

Connect the 24 VDC power adaptor to the power socket on the rear of the unit.

3.

Connect the unit to your PC using the provided USB-B cable, or an Ethernet cable if
preferred.

I.

If the unit is not detected, or driver installation fails, please refer to the SMU USB
Driver Installation Guide found on the USB memory stick.

9.

Operation

9.1

Measurement Types

The Ossila LED IVL software can perform 2 different types of measurements. Each measurement
type can be selected using the tabs at the top of the window. The available measurements are:

1.

Characterisation (

Section 9.1.1

2.

Lifetime (

Section 9.1.2

Each measurement type requires several settings to be selected before it can be performed.
Settings that are shared between all measurements are detailed in

Section 9.3

. Measurement-

specific settings are detailed in

Sections 0

, and

Note:

The Ossila LED IVL software and Source Measure Unit USB drivers can also be

downloaded from

ossila.com/pages/software-drivers

«
...
10
11
12
13
14
...
»

Содержание T2005




























Отзывы:

Нет отзывов

Похожие инструкции для T2005

Бренд: D-tect Systems Страницы: 19

Бренд: LaserLine Страницы: 24

Бренд: dbx Страницы: 2

Бренд: Keithley Страницы: 201

Бренд: Garmin Страницы: 120

Бренд: ICP DAS USA Страницы: 71

HYDROTECHNIK MultiHandy 2025

Бренд: ICS Страницы: 8

Бренд: ICT International Страницы: 24

Бренд: janitza Страницы: 12

Бренд: lanry Страницы: 2

Бренд: lanry Страницы: 29

Бренд: Rodstation Страницы: 28

QI-POWER-485-300

Бренд: QEED Страницы: 2

Бренд: Omega Страницы: 20

Бренд: Scaletron Страницы: 63

Бренд: Lumel Страницы: 40

Бренд: Omega Страницы: 22

Бренд: Hameg Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды