background image

Symptom

 

Component 
Check Order

 

Notes

 

Solution

 

 
3. Battery Not 
Charging 
(cont).

 

 
3.4. Charging 
Test.

 

 
MK1 (2007-2009) & MK2 Chargers (2010-2011): Put the bike on 
charge, flick the switch at the wall and look at the LED on the 
charger. This should be green when not plugged  into the bike ; red 
when you are charging the batteries and should trip to green after 
around 4-5 hours indicating a full charge. If it does not do this then 
you may not be getting any charge to the batteries or the batteries, 
due to their condition, may be unable to accept an adequate 
charge. 
MK3 Chargers (2012):  These chargers operate slightly differently. 
1. plug the charger into the mains outlet – the light on the charger 
will flash green and then turn to solid green. 2. plug the charger 
lead into the charge port on the bike – the light will flash red 
indicating the batteries are charging. 3. once the batteries are fully 
charged – the light will turn to solid green. If it does not do this 
then you may not be getting any charge to the batteries or the 
batteries, due to their condition, may be unable to accept an 
adequate charge.

 

 
1. Order a replacement Charger. 
In this case it is advisable to talk 
your symptoms through with a 
member of the OSET technical 
team.

 

 
3.5. Charge 
Port.

 

 
Check the condition of the charge port. As with all things electrical 
it is important to have good contact at the connection. Look for any 
signs of damage, debris or corrosion that could be causing a 
problem. Remove the rear splash guard so you can inspect the 
wiring at the rear of the charge port, this should have well soldered 
connections insulated by a resin material with two small wires, one 
of which connects at small black connector with the controller, 
while the other connects in the same way to the wiring harness. 
Check that both these connections are intact and that the wiring is 
still well insulated.

 

 
1. Any damage to this will 
require a replacement Charge 
Port.

 

22 

Содержание 2012 12.5 24V
































Отзывы: