manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Руководство оператора

Поделиться
Скачать
Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 40

OPERATION AND FIELD SETTINGS

DR12x2 Row Hopper Planter OM-EN 

5-4

Flex Settings

NOTES:

•

Left side wing procedure is shown. Right side wing

procedure is similar.

•

When the toolbar is placed in the “flex” setting, this
allows the toolbar wings to pivot freely about the
wing hinge in order to “float” over uneven field
terrain. Because of this, when the machine is raised
at the end of the field, the toolbar wings will “droop”
down approximately 8 degrees, reducing ground
clearance for turning the machine around. The
ground clearance should be adequate for turning the 
machine around at the end of the field in the “flex”
setting; however, if this is not desired, you may place 
the toolbar in the “up-flex-only” setting to not allow
the toolbar wings to flex down, only up. See
“Up-Flex-Only Settings” on page 5-5.

1. Park implement on a clean, level surface; strong

enough to support the weight of the machine.

DANGER

!

Avoid crushing. Failure to follow this information will 
result in death or serious injury. Use appropriate stands 
to support the implement.

2. Support the wing (1) with a minimum 5-ton stand (3)

and lower machine until tension is taken off the float

 

link 

lock 

pins.

ORM000138

Figure 5-3

CAUTION

!

Avoid pinch points. Failure to follow this information 
may result in minor or moderate injury. Potential pinch 
points are created when changing implement setting.

3. Remove lynch pin (6) and remove float link lock pin

(7) from the rigid position (8).

4. Place the float link lock pin in the storage position (9)

and install lynch pin.

ORM000144

Figure 5-4

1) Wing

3) Stand

2) Center section

4) Strut

2

1

3

4

4) Strut

7) Float link lock pin

5) Float link plate (2 used)

8) Rigid position

6) Lynch pin

9) Storage position

4

6

8

9

7

5

Содержание 125-087-02-EN-OM































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды