manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Руководство оператора

Поделиться
Скачать
Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 33

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN 

4-9

5. Loosen jam nut (9) and nut (10).
6. Remove strut pin (11) and centering pin (12), and 

disconnect the strut (15) from the float links (13).

NOTE: 

The wing fold cylinder (14) can be manipulated to 

reduce the tension on the pins and make it easier 
during removal.

ORM000139

Figure 4-12

7. With the strut (15) disconnected from the float links, 

screw the threaded end (16) clockwise to raise the 
wing or counterclockwise to lower the wing. Each full 
turn of the strut end results in approximately a 0.5° 
change to the wing. Use the previously noted 
levelness measurements to make the adjustments.

ORM000140

Figure 4-13

8. Install strut pin and centering pin, and connect the 

strut to the float links.

NOTE: 

The wing fold cylinder can be manipulated to 

reduce the tension on the pins and make it easier 
during installation.

9. Raise the machine and check the levelness of the 

wing compared to the center section.

10. If the wing angle is still lower than or more than 2° of 

the center section, repeat leveling procedure.

11. If the wing is within the levelness range, tighten the 

nut and jam nut.

9) Jam nut

13) Float link (2 used)

10) Nut

14) Wing fold cylinder

11) Strut pin

15) Strut

12) Centering pin

10

9

11

13

12

15

14

15) Strut

16) Threaded end

15

16

Содержание 125-087-02-EN-OM































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды