manualshive.com logo in svg

Orthman 125-087-02-EN-OM, Руководство оператора

Поделиться
Скачать
Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 35

PREPARATION AND SETUP

DR12x2 Row Hopper Planter OM-EN 

4-11

Internal Toolbar Vacuum 

Circuitry

An internal toolbar vacuum circuit has been designed into 
the DR12x2 Row Hopper Planter. The vacuum air for the 
seed meters is routed from each row unit (1) to the 
internal space of the toolbar, which is then connected to a 
vacuum fan (3) via a flex hose connected to another 
internal toolbar vacuum inlet (4).

ORM000132

Figure 4-18

At the ends of each toolbar section (wings and center) on 
the bottom face, there are rubber plugs fitted on slots to 
seal the toolbar. The slots are machined out of the 
toolbar to serve as a means of access to the inner space 
of the toolbar if necessary. 

Hitch Pin Position

The DR12x2 Row Hopper Planter can be configured for 
single row or twin row planter operation. See the tractor 
operator’s manual for properly setting the row units for 
each operation. Attach the tractor to the appropriate hitch 
pin location for each setting. See “Implement-to-Tractor 
Connection” on page 4-4.

Single Row Planter

ORM000125

Figure 4-19

Twin Row Planter

ORM000124

Figure 4-20

1) Row unit (24 used)

3) Vacuum fan (3 used)

2) Row unit vacuum 

intlet (24 used)

4) Internal toolbar vacuum 

inlet (6 used)

1

3

1

2

4

2

4

1) Hitch pin
2) Hitch tug pin (2 used)

3) Dual mount hitch tug 

spacer (2 used)

1) Hitch pin
2) Hitch tug pin (2 used)

3) Dual mount hitch tug 

spacer (2 used)

2

3

2

3

1

2

3

2

3

1

Содержание 125-087-02-EN-OM































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды