Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 62

Orthman 125-087-02-EN-OM Скачать руководство пользователя страница 41

OPERATION AND FIELD SETTINGS

DR12x2 Row Hopper Planter OM-EN

5-5

Up-Flex-Only Settings

NOTES:

•

Left side wing procedure is shown. Right side wing

procedure is similar.

•

When the toolbar is in the “up-flex-only” setting, the
toolbar wings will not be allowed to “float” down. This
will cause the toolbar to only “float” over uneven field
terrain in certain situations, such as driving the
tractor through a depression in the field, but not
when driving the tractor over the crown of a hill.

1. Park implement on a clean, level surface; strong

enough to support the weight of the machine.

DANGER

!

Avoid crushing. Failure to follow this information will
result in death or serious injury. Use appropriate stands
to support the implement.

2. Support the wing (1) with a minimum 5-ton stand (3)

and lower machine until tension is taken off the float

link

lock

pins.

ORM000138

Figure 5-5

CAUTION

!

Avoid pinch points. Failure to follow this information
may result in minor or moderate injury. Potential pinch
points are created when changing implement setting.

3. Remove lynch pin (6) and remove float link lock pin

(7) from the rigid position (8).

4. Place the float link lock pin in the down flex stop

position (9) and install lynch pin.

ORM000145

Figure 5-6

1) Wing

3) Stand

2) Center section

4) Strut

2

1

3

4

4) Strut

7) Float link lock pin

5) Float link plate (2 used)

8) Rigid position

6) Lynch pin

9) Down flex stop position

4

8

9

7

5

6

«
...
39
40
41
42
43
...
»

Содержание 125-087-02-EN-OM































































Отзывы:

Нет отзывов