Optimum OPTimill F 150 Скачать руководство пользователя страница 88

Страница: 88 / 162

OPTIMUM

M A S C H I N E N - G E R M A N Y

Notes, messages and error messages

Version 1.1.6 dated 2014-10-16

Page 88

Original operating instructions

F150

700083

Asup2 execution error.

700084

Magazine rotation error.

700085

Magazine to home error.

700086

Magazine motor overloaded

700087

Arm motor overloaded

700088

Unclamp tool manually to confirm empty spindle for safety.

Possible cause

and remedy

•

First insertign of a tool

•



"First insertion of a tool“ on page 74

700089

Magazine gate manual operation active.

700090

Magazine manual rotation active.

700091

Manual tool unclamp active.

700092

Tool pocket manual up/down active.

700093

Arm manual rotation active.

700094

Safety door not locked,NC start disabled.

Possible cause

and remedy

•

Limit switch with door lock outputs a signal that the safety door is not locked.

•

Safety door not fully closed and locked.

700095

*** Service mode ***



"Quit the ATC-Service mode“ on page 76

700104

Magazine manual in/out active.

700105

Handwheel 1 is active. (External)

700106

Handwheel 1 is active. (HMI)

700107

Handwheel 2 is active. (HMI)

700108

Door not closed to the magazine

700109

Right-hand door is not closed

700110

Left door is not closed

700128

Z axis is not referenced, positioning by PLC not possible.

700136

Tool changer not at home, Z axis inhibited

700137

Tool changer at spindle switch error, Z axis inhibited

700146

Spindle cooler unit not ready !

700152

Spindle not enabled ?

Possible cause

and remedy

•

Enable spindle on machine control panel.

700153

Spindle hold.

700154

Tool not clamped, spindle stop

700155

M00/M01 Spindle stop.

700156

Tool changer not at home, Spindle stop.

Number

Message description

Содержание OPTimill F 150



































































































































































Результаты поиска

Содержание OPTimill F 150

Отзывы:

Похожие инструкции для OPTimill F 150

Бренды по названию

Популярные бренды

Optimum OPTimill F 150, Руководство по эксплуатации

Результаты поиска

Содержание OPTimill F 150

Отзывы:

Похожие инструкции для OPTimill F 150

Бренды по названию

Популярные бренды