Optimum OPTimill F 150 Скачать руководство пользователя страница 87

Страница: 87 / 162

OPTIMUM

M A S C H I N E N - G E R M A N Y

Notes, messages and error messages

Version 1.1.6 dated 2014-10-16

Page 87

Original operating instructions

F150

700028

Tool data error

possible rem-

edy

•

Check tool table!

700030

Machine control panel error (MCP)

possible rem-

edy

Check type / MD / connection.

700031

Magazine in / out error.

700032

Waiting for SINAMICS ready. . .

700033

Operator door safety check, open door and close it again.

Cause and

solution

Safety door needs test, open then close it again.
•

Press the push button "door open - close"

•

Open the door and close the door again completely.

•

Press after closing the door the push button "RESET.



"Switching on the CNC machine“ on page 73

700040

Waiting for tool clamped.

700041

Waiting for tool unclamped.

700044

Tool probe Low battery

700046

Tool probe error

700048

Coolant motor overloaded

Possible cause

and remedy

•

Motor protection switch of the coolant pump is faulty.

•

Motor protection switch setting faulty.

•

Coolant pump is sucking air.

•

Shut-off cock is closed.

•

Pump or drive motor defective.

Possible cause

and remedy

•

Contactor of the coolant motor signals an incorrect switch status.

700050

Coolant level low.

Possible cause

and remedy

•

Fill up coolant

•

Float switch in the central oil lubrication

700051

CTS coolant motor overloaded.

700052

CTS recycle motor overloaded.

700053

CTS sub-tank level low, no coolant suction.

700055

CTS inlet filter clogged.

700056

CTS sub-tank level high.

700060

Spindle oil cooler alarm !

700064

Waiting for tool change . . .

700075

Waiting for gear changing. . .

700080

Asup1 initialise error, check PLCASUP1.SPF

700081

Asup2 initialise error, check PLCASUP2.SPF

700082

Asup1 execution error.

Number

Message description

Содержание OPTimill F 150



































































































































































Результаты поиска

Содержание OPTimill F 150

Отзывы:

Бренды по названию

Популярные бренды

Optimum OPTimill F 150, Руководство по эксплуатации

Результаты поиска

Содержание OPTimill F 150

Отзывы:

Бренды по названию

Популярные бренды