Onicon FT-3100 Скачать руководство пользователя страница 30

Страница: 30 / 36

FT-3100 TRANSMITTER PROGRAMMING GUIDE

ONICON Incorporated 727.447.6140

Page 30

onicon.com

Display Language

[Language = GB]

Contrast Adjustment

[Contrast = X]

Display/User Interface Inactivity Time Interval [Disp. times = s XXX]
Display Refresh Frequency

[D. rate = Hz X]

Enable Partial Totalizers

[Part. tot. = OFF]

Enable Negative Totalizers

[Neg. tot. = OFF]

Enable Net Totalizers

[Net tot. = OFF]

Enable Quick Start Menu

[Quick start = ON]

Default Display Page

[Disp. fn. = X]

Default Lock

[Disp. lock = OFF]

Select English (GB) or Italian (IT) for display text.
To change the existing setting, press enter to access the function. Use the up

arrow key to change the setting. Press enter to accept the change and exit the

function. Press escape to exit the program mode.

Table of Contents

Set the desired contrast level to optimize viewing. The allowable range is 0 to 9.
To change the existing setting, press enter to access the function. Use the up

arrow key to change the setting. Press enter to accept the change and exit the

function. Press escape to exit the program mode.

Table of Contents

This function sets the time interval for returning to normal operation following

a period of inactivity when using the display/user interface. Allowable settings

range from 20 to 255 seconds.
To change the setting, press enter to access the function. Use the right arrow

key to move the cursor and the up arrow key to change the value. Press enter to

accept changes and exit the function. Press escape to exit the program mode.

Table of Contents

This function sets the display refresh rate. It is used to optimize viewing. It does

not affect the data refresh rate. The settings are 1, 2, 5 or 10 Hz.

To change the existing setting, press enter to access the function. Use the up

arrow key to change the setting. Press enter to accept the change and exit the

function. Press escape to exit the program mode.

Table of Contents

Display Language

[Language = GB]

Contrast Adjustment

[Contrast = X]

Display/User Interface

Inactivity Time Interval

[Disp. times = s XXX]

Display Refresh Frequency

[D. rate = Hz X]

3.8 MENU 9 - DISPLAY

Содержание FT-3100





































Результаты поиска

Содержание FT-3100

Отзывы:

Похожие инструкции для FT-3100

Бренды по названию

Популярные бренды

Onicon FT-3100, Руководство по программированию

Результаты поиска

Содержание FT-3100

Отзывы:

Похожие инструкции для FT-3100

Бренды по названию

Популярные бренды