Onicon FT-3100 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

background image

FT-3100 TRANSMITTER PROGRAMMING GUIDE

ONICON Incorporated 727.447.6140

Page 27

onicon.com

When enabled, this function allows the autozero calibration function to be

remotely activated via the transmitter’s pulse input.
To change the existing setting, press enter to access the function and use the up

arrow key to turn the function on or off. Press enter to accept the change and

exit the function. Press escape to exit the program mode.

Table of Contents

When enabled, this function allows the pulse input to be used to remotely

change the flow range to full scale flow rate 2 [FS2 = Gal/m XXX.X] in SCALES

menu (menu 3).

Note: this function cannot be used when the autorange [Autorange = OFF] function

in MEASURE menu (menu 4) is enabled.

To change the existing setting, press enter to access the function and use the up

arrow key to turn the function on or off. Press enter to accept the change and

exit the function. Press escape to exit the program mode.

Table of Contents

Activate Autozero Calibration

via Pulse Input

[Calibration = OFF]

Change Flow Range via

Pulse Input

[Range change = OFF]

«
...
25
26
27
28
29
...
»

Содержание FT-3100





































Отзывы:

Нет отзывов

Похожие инструкции для FT-3100

Бренд: Mammut Страницы: 40

Бренд: Icom Страницы: 9

Бренд: gefran Страницы: 8

Бренд: Micrel Страницы: 47

Бренд: Icom Страницы: 32

Бренд: AUDIOropa Страницы: 88

Бренд: M-system Страницы: 2

Бренд: Micron Страницы: 4

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 84

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 72

Platinum standard Series

Бренд: ABB Страницы: 122

Бренд: ABB Страницы: 24

Бренд: ABB Страницы: 40

Бренд: ABB Страницы: 110

Бренд: ABB Страницы: 82

Бренд: ABB Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды