ON Semiconductor NCV91300 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 23

background image

EVBUM2789

www.onsemi.com

12

GUI SOFTWARE

Once hardware is properly installed and set up, user may

use the Graphical User Interface software (GUI in the rest of
the document) to set up NCV91300 and read configurations

At start up, the GUI will first read NCV91300

configuration. Please make sure that hardware is supplied
prior to GUI startup. Otherwise, the following error will be
displayed

Figure 12.

If during software power up, all the controls are empty,

please verified I

2

C address and ribbon cable insertion or

board to board connection.

Then, the main GUI screen is displayed

Figure 13. GUI Main Screen

«
...
10
11
12
13
14
...
»

Содержание NCV91300
























Отзывы:

Нет отзывов

Похожие инструкции для NCV91300

Бренд: Acer Страницы: 12

Бренд: MSI Страницы: 19

Бренд: NXP Semiconductors Страницы: 12

AR0140CS2M00AUEAH3-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: LITETRONICS Страницы: 2

Бренд: Supermicro Страницы: 90

Бренд: Analog Devices Страницы: 24

Бренд: ECS Страницы: 64

Бренд: JETWAY Страницы: 40

Бренд: VIA Technologies Страницы: 86

ISL9122AIIN-EVZ

Бренд: Renesas Страницы: 17

Бренд: Supero Страницы: 92

Бренд: Mercury Страницы: 57

Бренд: JETWAY Страницы: 47

Бренд: Gigabyte Страницы: 75

KIT34704BEPEVBE

Бренд: NXP Semiconductors Страницы: 39

Бренд: C-Control Страницы: 8

Бренд: DFI Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды