SCR053
Sensor Remote Programmer
OPERATION INSTRUCTIONS
SPECIFICATIONS
Power supply
2 x AAA 1. 5V battery, Alkaline preferred
Carrying case
RC-100 in carrying case
Communication 940 nm Infrared Tx & Rx
Upload range
Up to 15 m (50 ft.)
Op. temperature 0
°
C-50
°
C (32
°
F-122
°
F)
Dimensions
123x70x20.3 mm (4. 84"x2.76" xO. 8")
中
REMOTE
with carrying case
A
WARNING
Remove the batteries from compartment if the remote will not be used in 30 days.
OVERVIEW
The remote control Wireless IR Configuration Tool is a handheld tool for remote configuration of
IR-enabled fixture integrated sensors. The tool enables device to modify via pushbutton without
ladders or tools, and stores up to four sensor parameter modes to speed configuration of multiple
sensors.
The remote control uses bidirectional IR communication to send and receive sensor settings at
mounting height up to 50 feet. The device can display previously established sensor parameters,
copy parameters and send new parameters or store parameter profiles. For projects where identical
settings may be desired across a large number of areas or spaces, this capability provides a
streamlined method of configuration. Settings can be copied throughout a site, or in different sites.
LED INDICATORS
LED
DESCRIPTION
LED
DESCRIPTION
To select the current surrounding lux
To Set the output level (in%) of
value as the daylight threshold. This
BRIGHTNESS connected lighting during
＠
feature enables the fixture to function
occupancy
well in any real application
circumstances.
The built-in daylight sensor stops
SENSITIVITY To set the occupancy sensing
＠
working, and all motion detected
sensitivity of the Sensor
could turn on the lighting fixture, no
matter how b
「
ight the natural light is.
To set the output level (in%) of
The time that the Sensor will turn
connected lighting during vacancy.
HOLD TIME off(if you choose stand-by level is STAND-BY DIM The sensor will regulate the lighting
0) or dim the light to a low level
output at the set level. Setting the
after the area is vacated
STAND BY DIM at O means light full
off during vacancy.
DAYLIGHT To represents various thresholds of
To represents the time that the
SENSOR
natural light level for the Sensor .
STAND-BYTIME Sensor will keep the light at low dim
level after the HOLD TIME elapsed.
BUTTON OPERATION
BUTTON
DESCRIPTION
BUTTON
DESCRIPTION
Press the "ON/OFF" button, the
light goes to pe
「
manent on or
Press "Auto" button, the sensor starts to
＠
permanent off mode, and the
令
function and all settings remain the same
sensor is disabled.(MUST press
as the latest status before the light is
"Auto"button to quit this mode for
switched on/off.
Setting.
Display the current/lastest setting
The button" TEST" is for testing purpose
令）
parameters in LED indicators(the
sens仆ivity only. afle
「
you choose sens仆ivity
LED indicators will on for showing
thresholds, then you press"TEST" button,
the setting parameters)
割
The sensor goes to test mode(hold time is
only 2s) automatically ,meanwhile the
令
Press "RESET" button, all settings
stand-by period and daylight sensor are
go back to settings of dip Switch in
disabled Press "AUTO" button to quit from
sensor
this mode
@�
Enter in the setting condition, and
Press this button for open or close the smart
Navigate to UP and Down for choose
photocell sensor which take place of normal
selected parameters in LED indicators.
photocell sensor switch When remote
control enters in se廿ing conduction, you can
Navigate to LEFT and RIGHT for
choose open and close the smart photocell
�®
sensor. If this smart photocell sensor open,
choose selected parameters in
2 Leds indicators of daylight sensor are on
LED indicators.
for choose photocell sensor setpoint on/off
to light, and Stand by lime is only 8. When
＠
Keep records of selected parameters
the natural light level exceeds setpoint off to
light, the lights will turn off even if when the
in remote cont
「
ol or 1n Mode 1 o
「
＠
space is occupied once the natural light
mode 2 mode 3,mode 4
level exceeds this setpoint off to light, the
sensor will wait and monitor for 1 minute in
今
Upload the selected parameters to
order to confirm the natural light level
increase is not temporary before forcing the
sensors.
lights to go off. When the natural light level
lower than setpoint on to light, the lights will
@8
turn on even when the space is not occupied.
4 Scene modes with preset
when natural light level goes lower than this
setpoint on to light, the sensor will wait and
parameters which are available to
monitor for 1 minute in order to confirm the
＠今
be changed and saved in modes
natural light level decrease is not temporary
before forcing the lights go on
SETTING
The SETTING Content contains all available settings and parameters for remote sensors. It
allows you to change the available control, parameters, and operation of the sensor from factory
default or current parameters.
NOTE:the setting works only in Auto mode.
Change multiple settings of sensor(s)
1.Press DISP button(if you push ON/OFF button before you push DISP button, the sensor is locked,
so please push "AUTO" button to unlock the sensor ,and then push DISP button), the controler
leds indicators will show the latest parameters.
2.Press @ or®enter in the setting condition, navigate to the desired setting by pressing
@®@®to select the new parameters.
3.Press ok to confirm all setting and saving.
4.Aim at the target sensor and press SEND to upload the new parameter. light will be one time and off ,
as confirm.
-1-
-2-
Содержание SCR053
Страница 2: ......
