background image

Read and Understand This QIG

 

 

KP100L Quick Installation Guideline 

 

 

2

 

Read and Understand This QIG 

 
Read and understand this QIG before using the KP100L. Please consult your OMRON representative if 
you have any questions or comments. 

 
Warranty and Limitations of Liability 

WARRANTY 

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a 
period of five years (or other period if specified) from date of sale by OMRON. 
 
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING 
NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE 
PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS 
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED 
USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. 

 

LIMITATIONS OF LIABILITY 

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL 

 

DAMAGES, 

LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, 
WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. 
 
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which 
liability is asserted. 
 
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS 
REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE 
PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO 
CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. 

 

Application Considerations 

SUITABILITY FOR USE 

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the 
combination of products in the customer's application or use of the products. 
 
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings 
and limitations of use that apply to the products. This information by itself is not sufficient for a complete 
determination of the suitability of the products in combination with the end product, machine, system, or other 
application or use. 
 
The following are some examples of applications for which particular attention must be given. This is not 
intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses 
listed may be suitable for the products: 
 
• Uses involving potential chemical contamination or electrical interference, or conditions or uses not described 
in this manual. 
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, 
amusement machines, vehicles, safety equipment, and installations subject to separate industry or government 
regulations. 
• Systems, machines, and equipment that could present a risk to life or property. 
 
Please know and observe all prohibitions of use applicable to the products. 
 
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY 
WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE 
RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE 
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 

Содержание KP100L-OD - QUICK LINE




























Отзывы: