Omron KP100L-OD - QUICK LINE Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 27

background image

4. Installation

KP100L Quick Installation Guideline

16

Mount Inverter Straight Never mount tilted to front Never use in tower orientation

[Example of installation]

■

Installation

(1) Set up "Mounting base plate" in the place where the weight (41.5kg) of KP100L can be endured.

The installation location should endure the torque of 176N

⋅

m with each installation screw.

Use the reinforced board when strength of the wall is insufficient.
Please prepare the board to reinforce it .

(2) Mark the positions of the 8 outer mounting holes onto the wall with the mounting base plate.
(3) Drill the 8 marked holes in the wall, and then drive the 8 Snap Bushings by the hammer into the

wall, when the wall is a hard wall like concrete.

(4) Fix the mounting base plate to the wall by using 8 mounting screws of the attachment.

Snap bushing

Use Snap Bushings when the wall is

a hard wall like concrete

8mm diameter
55mm depth

OK

NG

Never mount tilted

«
...
15
16
17
18
19
...
»

Содержание KP100L-OD - QUICK LINE




























Отзывы:

Нет отзывов

Похожие инструкции для KP100L-OD - QUICK LINE

Бренд: D&H Страницы: 70

Maestro Pro 01925

Бренд: Olimpia splendid Страницы: 60

DCS SCARLATTI DAC

Бренд: Data Conversion Systems Страницы: 26

Бренд: N-Tron Страницы: 2

Бренд: Altera Страницы: 87

Бренд: CTC Union Страницы: 44

Бренд: TANDBERG Страницы: 196

Бренд: Phrontier Technologies Страницы: 16

Gold Link Dac III

Бренд: MSB Technology Страницы: 12

JNTHBCBA0001BEAU

Бренд: TECO Страницы: 98

Бренд: Weidmuller Страницы: 13

Бренд: Miteq Страницы: 74

Бренд: SIP Страницы: 8

Бренд: Comprehensive Страницы: 13

Бренд: CYP Страницы: 88

Бренд: NovaStar Страницы: 9

Бренд: Must Страницы: 16

SieiDrive EXP-FIH

Бренд: gefran Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды