background image

Safety Precautions

 

 

KP100L Quick Installation Guideline 

 

 

6

Important installer information: 

Observe the following warnings and cautions when installing the KP100L. 

    WARNING 

Significant property damage may possibly occur. Do not use the product 
in other country than the designated country. 

Significant property damage may possibly occur. Do not use the product 
with a mistake of the country setting. 

 

Functional lesion by injury and fire damage may possibly occur.

 

Do not 

remove the MC cap on the back of the product when you exchange the 
FAN Assembly. 

Significant property damage may possibly occur. Execute the installation 
by a person who has the qualification that authorized by the electric 
power company in the region. 

Electric shock and significant property damage may possibly occur. Do a 
correct connection after confirming the polarity of the cable from the 
solar modules and from the grid. 

Fire by loose connection of AC terminal block may possibly occur. 
Confirm there is no looseness in the screw of the AC terminal block 
during the maintenance. 
When using the product by the state that tightening the screw of AC 
terminal block is insufficient, fire by loose connection may possibly 
occur. 
Insert the electric cable in the inner of AC terminal block by using special 
Rod terminal and crimping pliers, and tighten the screw by tightening 
torque of 1.2-1.5N

m. 

 

Fire by loose connection of the MC connector may possibly occur. Use 
the specialized tool for the crimping process of the MC connector. Insert 
the MC connector surely until locking. 

Injury by electric shock may possibly occur. Read this manual before 
installation, operating and maintenance of the product, and follow the 
instructions carefully. 

Injury or functional lesion by electric shock or burn injury may possibly 
occur. Do not install the product in places that child's hand reaches. 

Injury by electric shock may possibly occur. Do not open the cover 
foreside R during energizing. 

Significant injury by electric shock may possibly occur. Do not touch the 
terminal of the MC connector. Do not remove the MC connector excluding 
the instruction of this manual. 

 

Significant injury by electric shock may possibly occur. Do not open the 
cover foreside R and not touch the MC connector for three minutes after 
turning OFF the breaker of the grid side and the solar module side. 

 

Injury by electric shock may possibly occur. Connect the PE cable to the 
earth. 

Содержание KP100L-OD - QUICK LINE




























Отзывы: