manualshive.com logo in svg

Omron H2A -, Руководство пользователя

Поделиться
Скачать
Omron H2A - Скачать руководство пользователя страница 101

H3DR-H

H3DR-H

101

Time Ranges

Time ranges

Setting

Setting range

Min. power ON time

S-series

Time scale: x 0.1

0.1 to 1.2 s

0.1 s min.

Time scale: x 1

1 to 12 s

L-series

Time scale: x 1

1 to 12 s

0.3 s min.

Time scale: x 10

10 to 120 s

Note:

If the above minimum power ON time is not secured, the H3DR may not operate. Be sure to secure the above minimum power ON time.
Allow at least 3 s for repeat synchronization of time-out operations (see Precautions on page 107).

Ratings

Rated supply voltage (see note)

100/110/120 VAC (50/60 Hz), 200/220/240 VAC (50/60 Hz), 24 VAC/DC (50/60 Hz),
48 VAC/DC (50/60 Hz)

Operating voltage range

85% to 110% of rated supply voltage

Power consumption

100/110/120 VAC: approx. 0.5 VA
200/220/240 VAC: approx. 0.8 VA
24 VAC/DC:

approx. 0.17 VA (AC), 0.13 W (DC)

48 VAC/DC:

approx. 0.36 VA (AC), 0.34 W (DC)

Control outputs

Contact output: 5 A at 250 VAC, resistive load (cos

%

= 1)

Note:

A power supply with a ripple of 20% max. (single-phase power supply with full-wave rectification) can be used with each DC Model.

Characteristics

Accuracy of operating time

!

1% FS max. (1% FS

!

10 ms max. in ranges of 1.2 s)

Setting error

!

10% FS

!

0.05 s max.

Influence of voltage

!

0.5% FS max. (

!

0.5% FS

!

10 ms in ranges of 1.2 s)

Influence of temperature

!

2% FS max. (

!

2% FS

!

10 ms in ranges of 1.2 s)

Insulation resistance

100 M

$

min. (at 500 VDC)

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min (between current-carrying metal parts and exposed
non-current-carrying metal parts)
2,000 VAC, 50/60 Hz for 1 min (between control output terminals and operating circuit)
1,000 VAC, 50/60 Hz for 1 min (between contacts not located next to each other)

Impulse withstand voltage

3 kV (between power terminals) for 100 to 120 VAC, 200 to 240 VAC
1 kV for 24 VAC/DC, 48 VAC/DC
4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts)
for 100 to 120 VAC, 200 to 240 VAC
1.5 kV for 24 VAC/DC, 48 VAC/DC

Noise immunity

!

1.5 kV (between power terminals), square-wave noise by noise simulator (pulse width:

100 ns/1

&

s, 1-ns rise)

Static immunity

Malfunction: 4 kV
Destruction: 8 kV

Vibration resistance

Destruction:10 to 55 Hz with 0.75-mm single amplitude each in three directions
Malfunction:10 to 55 Hz with 0.5-mm single amplitude each in three directions

Shock resistance

Destruction: 980 m/s

2

(100G) each in three directions

Malfunction: 98 m/s

2

(10G) each in three directions

Ambient temperature

Operating:--10

"

C to 55

"

C (with no icing)

Storage:

--25

"

C to 65

"

C (with no icing)

Ambient humidity

Operating: 35% to 85%

Life expectancy

Mechanical:10 million operations min. (under no load at 1,200 operations/h)
Electrical:

100,000 operations min. (5 A at 250 VAC, resistive load at 1,200 operations/h)

EMC

Emission Enclosure:

EN55011 Group 1 class A

Emission AC Mains:

EN55011 Group 1 class A

Immunity ESD:

IEC801-2:

4 kV contact discharge (level 2)
8 kV air discharge (level 3)

Immunity RF-interference: ENV50140: 10 V/m (80 MHz to 1 GHz) (level 3)
Immunity Conducted Disturbance:

ENV50141: 10 V (0.15 to 80 MHz) (level 3)

Immunity Burst:

IEC801-4:

2 kV power-line (level 3)
2 kV I/O signal-line (level 4)

Enclosure ratings

IEC: IP40

Weight

Approx. 135 g

Содержание H2A -







































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды