Olympus CF Q160AL/I Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 74

background image

50

Chapter 3 Cleaning, Disinfection and Sterilization Procedures

EVIS EXERA GIF/CF/PCF TYPE 160 Series REPROCESSING MANUAL

3.6

High-level disinfection

After manual cleaning, disinfect the endoscope according to the procedures
described below.

Equipment needed

Prepare the following equipment:

All disinfection steps should be performed with the
endoscope and all equipment completely immersed. While
they are immersed, if the equipment is connected to the
endoscope or any part of them is not immersed completely,
disinfectant solution may not adequately contact all surfaces
of the equipment.

Preparation

1.

Fill a basin with disinfectant solution at the temperature and concentration
recommended by the disinfectant manufacturer. Use a basin which is at
least 40 cm by 40 cm (16” by 16”) in size and deep enough to allow the
endoscope to be completely immersed.

2.

Connect the channel plug and the injection tube to the endoscope.

3.

Attach the auxiliary water tube to the auxiliary water inlet (for endoscopes
with auxiliary water feeding only).

• Personal protective equipment
• Clean, lint-free cloths
• Large basin
• Disinfectant solution
• Channel plug

(MH-944)

• Injection tube

(MH-946)

• Auxiliary water tube

(MAJ-855 for endoscopes with
auxiliary water feeding only)

«
...
52
53
54
55
56
...
»

Содержание CF Q160AL/I











































































Отзывы:

Нет отзывов

Похожие инструкции для CF Q160AL/I

Бренд: YATEK Страницы: 72

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Бренд: Ognibene Страницы: 28

Бренд: Hameg Страницы: 24

Бренд: Vaisala Страницы: 118

Бренд: H&S Страницы: 42

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренд: Velp Scientifica Страницы: 32

Бренд: Velleman-Kit Страницы: 32

Бренд: Yacht Devices Страницы: 32

INTRA PROPHYwiz 181 P

Бренд: KaVo Страницы: 22

Бренд: Festo Страницы: 40

Бренд: Neurotech Страницы: 24

Бренд: PARAMOUNT BED Страницы: 120

Бренд: PARAMOUNT BED Страницы: 28

Бренд: FOAMICO Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды