Olympus CF Q160AL/I Скачать руководство пользователя страница 33

Страница: 33 / 74

Chapter 3 Cleaning, Disinfection and Sterilization Procedures

EVIS EXERA GIF/CF/PCF TYPE 160 Series REPROCESSING MANUAL

Flush detergent solution and air into the auxiliary water

channel (for endoscopes with auxiliary water feeding only)

• Do not cap the auxiliary water inlet during reprocessing.

• If the auxiliary water tube is not connected to the auxiliary

water inlet, uncap the auxiliary water inlet and connect the
auxiliary water tube (see Figure 3.15).

Prior to reprocessing endoscopes equipped with auxiliary
water feeding, attach the auxiliary water inlet cap to the
auxiliary water inlet and open the cap (see Figure 3.15).

Immerse the distal end of the insertion tube in the water.

Using the 30 cm

(30 ml) syringe, slowly flush detergent solution through

the auxiliary water channel several times until no bubbles exit the distal end.

Using the 30 cm

(30 ml) syringe, slowly flush water through the auxiliary

water channel several times.

Using the 30 cm

(30 ml) syringe, slowly flush air through the auxiliary water

channel several times until a steady stream of bubbles exits the distal end.

Figure 3.15

Luer port

Auxiliary water inlet

Endoscope connector

Auxiliary water inlet cap

Clean

water

Syringe

Auxiliary water tube

Содержание CF Q160AL/I











































































Результаты поиска

Содержание CF Q160AL/I

Отзывы:

Похожие инструкции для CF Q160AL/I

Бренды по названию

Популярные бренды

Olympus CF Q160AL/I, Инструкция по эксплуатации

Результаты поиска

Содержание CF Q160AL/I

Отзывы:

Похожие инструкции для CF Q160AL/I

Бренды по названию

Популярные бренды