Olivetti d-Copia 12 Скачать руководство пользователя страница 54

Страница: 54 / 78

5-10

Service Manual

Y101700-5

5.4.2 DV bias adjustment

• A digital multi meter with internal resistance of 1GW

must be used for correct adjustment.

5.4.2.1

Procedures

1. Set the digital multi meter range to DC500V.
2. Set the positive side of the test rod to the connector

CN-10-1 (DV BIAS) and set the negative side to the
connector CN10-2 (FG).

3. Execute SIM 8-1. (The developing bias is outputted for

30 sec.)

4. Adjust the control volume (VR-121) so that the output

voltage is – 400 ±5V.

5.4 High voltage adjustment

5.4.1 Main charger (Grid bias)

• Use a digital multi meter with internal resistance of

10MW or more measurement.

• After adjusting the grid LOW output, adjust the HIGH

output.
Do not reverse the sequence.

5.4.1.1 Procedures

1. Set the digital multi meter range to DC700V.
2. Set the positive side of the test rod to the connector

CN11-3 (GRID) of high voltage section of the power PWB
and set the negative side to the frame ground (radiating
plate).

3. Execute SIM 8-3. (The main charger output is supplied for

30 sec in the grid voltage LOW output mode.)

4. Adjust the control volume (VR-141) so that the output

voltage is – 400 ±20V.

5. Execute SIM 8-2. (The main charger output is supplied for

30 sec in the grid voltage HIGH output mode.)

6. Adjust the control volume (VR-142) so that the output

voltage is 580 ±10V.

Содержание d-Copia 12














































































Результаты поиска

Содержание d-Copia 12

Отзывы:

Бренды по названию

Популярные бренды

Olivetti d-Copia 12, Руководство по обслуживанию

Результаты поиска

Содержание d-Copia 12

Отзывы:

Бренды по названию

Популярные бренды