Oliver 732-N Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 49

Oliver 732-N Скачать руководство пользователя страница 3

732-N Front Load Slicer

0732S20001

0-2

INDEX (Continued)

REPLACEMENT PARTS SECTION (Continued)

Section Description

Document No.

Page No.

COVERS ------------------------------------------------------------ 0732S20010 --------------------------- 9-1
Drawing

------------------------------------------------------------------------------------------------

9-1

Parts List ----------------------------------------------------------------------------------------------- 9-2

PUSHER ------------------------------------------------------------ 0732S20011 -------------------------- 10-1
Drawing

-----------------------------------------------------------------------------------------------

10-1

Parts List ---------------------------------------------------------------------------------------------- 10-2

ROCKER ----------------------------------------------------------- 0732S20012 -------------------------- 11-1
Drawing

-----------------------------------------------------------------------------------------------

11-1

Parts List ---------------------------------------------------------------------------------------------- 11-2

DRIVEN PULLEY ------------------------------------------------- 0732S20013 -------------------------- 12-1
Drawing

-----------------------------------------------------------------------------------------------

12-1

Parts List ---------------------------------------------------------------------------------------------- 12-2

SLICE PARTS ----------------------------------------------------- 0732S20014 -------------------------- 13-1
Drawing

-----------------------------------------------------------------------------------------------

13-1

Parts List ---------------------------------------------------------------------------------------------- 13-2

ELECTRICAL ------------------------------------------------------ 0732S20015 -------------------------- 14-1
Drawing

-----------------------------------------------------------------------------------------------

14-1

Parts List ---------------------------------------------------------------------------------------------- 14-2

WIRING DIAGRAM 1-60-115/230 --------------------------- 0732S20016 -------------------------- 15-1

WARRANTY ------------------------------------------------------- GEN 040225

WARRANTY PROCEDURE------------------------------------ GEN 040226

RETURNED PARTS POLICY --------------------------------- GEN 040227

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

«
1
2
3
4
5
...
»

Содержание 732-N


















































Отзывы:

Нет отзывов