manualshive.com logo in svg

Oliver 732-N, Руководство пользователя по эксплуатации и инструкция, Страница: 25 / 49

Поделиться
Скачать
Oliver 732-N Скачать руководство пользователя страница 25

732-N Front Load Slicer

 

0732S20007  

6-12 

Adjusting The Gas Spring 
 

WARNING

 

      

ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE 

ATTEMPTING ANY TYPE OF MAINTENANCE TASK. 

 

CAUTION

 

      

FREQUENT ADJUSTMENT OF THE GAS SPRING IS NOT RECOMMENDED. 

 
The gas spring must be removed and relocated to adjust its force.  To remove the gas 
spring, see “Replacing the Gas Spring” above.  There are two gas spring pins welded to 
the frame.  The pin furthest from the front of the machine, (the standard position), should 
be used whenever possible.  The standard position gives a gentle force at the beginning 
of the slicing operation, (when it is most needed), which will allow the knives to start 
cutting and prevent damage to the product.  It also provides the most force at the end of 
the stroke to allow the cradle to finish its upward travel and the machine to shut off. 
 
The pin located in the high forward position should be used when greater force is 
desired as the product is first entering the knives. 
 

NOTE

 

      

NORMALLY DIFFICULT CUTTING BREADS REQUIRE LESS FORCE AT THE  

BEGINNING OF SLICING RATHER THAN MORE.

 

 

 
Using proper gas spring installation procedures, see “Replacing the Gas Spring”’ above, 
compress the spring and mount it on the desired pin. Secure it with a new clip. 
 

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Содержание 732-N


















































Отзывы:

Нет отзывов