manualshive.com logo in svg

Oliver 732-N, Руководство пользователя по эксплуатации и инструкция, Страница: 11 / 49

Поделиться
Скачать
Oliver 732-N Скачать руководство пользователя страница 11

732-N Front Load Slicer

 

0732S20006  

5-2 

Trouble Shooting (Continued) 

 
The Slicer Will Not Start (Motor Is Humming) 
 

CAUTION

 

      

DO NOT ALLOW THE MOTOR TO HUM WITHOUT STARTING. 
OVERHEATING CAN PERMANENTLY DAMAGE THE MOTOR. 

 

NOTE

 

      

A SPECIAL NON-VENTILATED MOTOR MUST BE USED WITH THIS SLICER. 

 

•

  The drive system is binding.  (Have a qualified service agent check for defective 

bearings or other restrictions to free movement.) 

 

•

  There is mechanical interference between other parts of the slicer.  (Have a qualified 

service agent evaluate the machine for adjustment or replacement of defective 
parts.) 

 

•

  The motor has failed.  (Have it checked by a qualified electrician.) 

 

 
 

The Slicer Stops Before Slicing is Complete 
 

•

  The upper limit switch is not adjusted properly.   (Have a qualified service agent 

adjust the switch.) 

 
 

The Slicer Does Not Automatically Stop Upon Completion of Slicing 
 

•

  The upper limit switch is not adjusted properly.   (Have a qualified service agent 

adjust the switch.) 

 

•

  The upper limit switch is defective.   (Have a qualified electrician check and replace 

the switch if required.) 

 

•

  A bread crust or other foreign object is preventing the cradle from returning to the top 

of its travel. 

 
 
 
 

Continued 

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Содержание 732-N


















































Отзывы:

Нет отзывов