manualshive.com logo in svg

Oliver 732-N, Руководство пользователя по эксплуатации и инструкция, Страница: 2 / 49

Поделиться
Скачать
Oliver 732-N Скачать руководство пользователя страница 2

732-N Front Load Slicer

 

0732S20001  

0-1 

INDEX 

 
Section Description

                                 

Document No.

                      

Page No. 

 

SAFETY INSTRUCTIONS -------------------------------------- 0732S20002 --------------------------- 1-1 

 

DESCRIPTION/SPECIFICATIONS --------------------------- 0732S20003---------------------------- 2-1 
 

Description -------------------------------------------------------------------------------------------------- 2-1  

 Specifications----------------------------------------------------------------------------------------------- 

2-1 

 

INSTALLATION INSTRUCTIONS ---------------------------- 0732S20004 --------------------------- 3-1 
 Slicer 

Installation 

------------------------------------------------------------------------------------------ 

3-1 

 

OPERATING INSTRUCTIONS -------------------------------- 0732S20005 --------------------------- 4-1 

 

 

TROUBLESHOOTING ------------------------------------------- 0732S20006 --------------------------- 5-1 
 

The Slicer Will Not Start (Motor is Not Humming) ------------------------------------------------  5-1 

 

The Slicer Will Not Start (Motor is Humming) ------------------------------------------------------ 5-2 

 

The Slicer Stops Before Slicing is Complete ------------------------------------------------------- 5-2 

 

The Slicer Does Not Automatically Stop Upon Completion of Slicing ----------------------- 5-2 

 

Bread Slices Vary in Thickness ------------------------------------------------------------------------ 5-3 

 

The Blade Frames are Knocking ---------------------------------------------------------------------- 5-3 

 

The Slicer Vibrates Excessively ----------------------------------------------------------------------- 5-3 

 

The Hand Lever Pulls Hard ----------------------------------------------------------------------------- 5-3 

 

The Bread is Cutting Slowly or is Being Damaged ----------------------------------------------- 5-4 

 

MAINTENANCE --------------------------------------------------- 0732S20007 --------------------------- 6-1 
 

Removing the Blade Frames --------------------------------------------------------------------------- 6-1 

 

Replacing the Blade Frames --------------------------------------------------------------------------- 6-4 

 

Changing the Blades ------------------------------------------------------------------------------------- 6-5 

 

Tightening the Belt ---------------------------------------------------------------------------------------- 6-7 

 

Replacing the Belt ----------------------------------------------------------------------------------------  6-8 

 

Replacing the Gas Spring ------------------------------------------------------------------------------  6-9 

 

Adjusting the Gas Spring ------------------------------------------------------------------------------ 6-12 

 

Adjusting the Blade Frames When Slices Vary in Thickness --------------------------------  6-13 

 

Adjusting the Clearance Between the Blade Frames ------------------------------------------   6-14 

 Lubrication 

------------------------------------------------------------------------------------------------- 6-15 

 Cleaning 

---------------------------------------------------------------------------------------------------- 6-15 

 

RECOMMENDED SPARE PARTS --------------------------  0732S20008 --------------------------- 7-1 

 

REPLACEMENT PARTS SECTION  

 

MAIN FRAME ---------------- ------------------------------------- 0732S20009 --------------------------- 8-1 
 Drawing 

------------------------------------------------------------------------------------------------- 

8-1 

 

Parts List ----------------------------------------------------------------------------------------------- 8-2 

 
 
 
 

  

Continued 

PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

Содержание 732-N


















































Отзывы:

Нет отзывов