Oki Pro1040 Скачать руководство пользователя

Страница: 29 / 118

- 29 -

If Other Messages Are Displayed

Message displayed on the

display screen

Error

code

ATTENTION

lamp

Causes and Troubleshooting

Reference

pages

The data will be deleted due to a

spot color order mismatch error.

Check the print cartridge

position and spot color settings,

and try to print again. To turn

off the display, press OK button

Please see HELP for details

7380

Blinking

The position of the white print cartridge

is different from that specified in the

printer driver.

Printing has been stopped, and the data

was deleted.

Check the order of the print cartridge

and the Spot Color setting, then print

once again.

Press the <OK> button to delete the

display on the display screen.

Check Waste Toner Box

Please see HELP for details

331

Blinking

The waste toner box is not set correctly.

Install the waste toner box correctly.

Firmware Update Error

Please retry

If network doesn’t work, please

try firmware update over USB

302

Firmware update failed.

Follow the instructions in the message.

Feeder Unit Not Installed

Shut down and Install Feeder

Unit

7305

Blinking

The unwinder is not installed.

Turn off the power, and then install the

unwinder.

Belt Unit Not Installed

Please see HELP for details

689

Blinking

The belt unit is not installed properly.

Press the <HELP> button, and solve

according to the guidance shown on the

Help screen.

Check Belt Unit

Please see HELP for details

330

Blinking

The belt unit is not installed correctly.

Install the belt unit correctly.

Unnecessary Print Cartridge

Error

Check the position of print

cartridge lift up lever

Please see HELP for details

7398

7399

Blinking

The lift up lever of the print cartridge is

not in the correct position.

Press the <HELP> button, and solve

according to the guidance shown on the

Help screen.

Install Paper Guide

Re-set the Paper Guide

Please see HELP for details

7384

Blinking

The paper guide is not set correctly.

Press the <HELP> button, and solve

according to the guidance shown on the

Help screen.

Open Cover

Paper was pulled out

7312

Blinking

Paper was forcefully extracted while

being fed.

Open the cover and if there are scraps

of paper, remove them, and then close

the cover.

Check Installed Paper Edge

Paper Edge Long Error

Press OK Button

Please see HELP for details

7308

Blinking

The mark on the leading edge of the

paper cannot be detected correctly.

Replace the paper, and then press the

<OK> button.

Press the <HELP> button, and solve

according to the guidance shown on the

Help screen.

Paper Width Error

Press OK Button

Please see HELP for details

7383

Blinking

The paper currently being used is

different from the paper settings in the

printer driver.

Replace the paper, and then press the

<OK> button.

Press the <HELP> button, and solve

according to the guidance shown on the

Help screen.

Содержание Pro1040























































































































Результаты поиска

Содержание Pro1040

Отзывы:

Похожие инструкции для Pro1040

Бренды по названию

Популярные бренды

Oki Pro1040, Руководство по обслуживанию

Результаты поиска

Содержание Pro1040

Отзывы:

Похожие инструкции для Pro1040

Бренды по названию

Популярные бренды