background image

IMPORTANT: The
brewcycle is adjusted
at the factory to fill a

standard 2.5 liter airpot with
2.2 liters of brewed coffee. The
duration of the brewcycle is set
between 2 minutes, 40 seconds
and 3 minutes.

• 

Water Source:

 

 

20 - 100 PSI (Minimum Flow Rate of 1 GPM)

• Electrical: 

 See attached schematic for your model.

Setup Steps

The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water
filter to the brewer. (NOTE: Some type of water filtration device must be used to maintain a trouble-free operation). In areas
with extremely hard water, we suggest that a sedimentary and taste & odor filter be installed. These will prolong the life of your
brewing system and enhance coffee quality.

The National Sanitation Foundation requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be

   

moved for cleaning underneath.

2. In some areas an approved backflow prevention device may be required between the brewer and

     

the water supply. (Check local plumbing codes).

Revised: April, 2002

MODELS INCLUDED

MODELS INCLUDED

MODELS INCLUDED

MODELS INCLUDED

MODELS INCLUDED
••••• TLP10
••••• TLP15
••••• TLP20
••••• TLP30*
••••• TLP61
* NOT UL LISTED

1

F

F

F

F

F

IND

IND

IND

IND

IND

     

OUT

OUT

OUT

OUT

OUT

     

MORE

MORE

MORE

MORE

MORE

ON

ON

ON

ON

ON

     

THE

THE

THE

THE

THE

     

WEB

WEB

WEB

WEB

WEB

.....

W I L B U R C U R T I S . C O M

W I L B U R C U R T I S . C O M

W I L B U R C U R T I S . C O M

W I L B U R C U R T I S . C O M

W I L B U R C U R T I S . C O M

  W

  W

  W

  W

  W

ILBUR

ILBUR

ILBUR

ILBUR

ILBUR

  C

  C

  C

  C

  C

URTIS

URTIS

URTIS

URTIS

URTIS

  C

  C

  C

  C

  C

OMP

OMP

OMP

OMP

OMPANY

ANY

ANY

ANY

ANY

, I

, I

, I

, I

, I

NC

NC

NC

NC

NC

.....

ISO 9001 REGISTERED

CAUTION: 

CAUTION: 

CAUTION: 

CAUTION: 

CAUTION: Please use
this setup procedure
before attempting to use

this brewer. . Failure  to follow the
instructions can result in injury or
the voiding of the warranty.

SYSTEM REQUIREMENTS

TLP Brewer Instructions

Important Safeguards/Conventions

WILBUR CURTIS COMPANY

Montebello, CA 90640

1. A ¼ flare water inlet fitting has been supplied for water line connection. Use tubing sized sufficiently to provide a minimum

of 1.0 GPM,

2. Connect the unit to an appropriate electrical power circuit.
3. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water level in the tank

rises to the correct volume, the heating elements will energize automatically. With ADS Systems there is no danger of
element burnout caused by an empty tank.

4. Turn on the control panel by pressing the ON/OFF button.
5. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F) as indicated by the READY-TO-BREW

indicator.

6. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
7. Run brew cycle of at least 16 ounces to purge the water line of any air trapped in the lines after filling.

BREWING COFFEE

1. Place airpot in

position, under the

sprayhead.

Place a new filter in

the brewcone.

2. Pour ground coffee

into the brewbasket.

3. Slide the brewcone

into position on

brew rails.

4. Wait until the READY-

TO-BREW light comes

on and then press the

desired BREW button.

The indicator light

above the selected

brew will begin flashing

when the brewcycle

starts.

C

W

W

W

W

WARNING:

ARNING:

ARNING:

ARNING:

ARNING:

 

To avoid

scalding, do NOT remove
brew cone while brew

indicator light is flashing.

CAUTION: 

CAUTION: 

CAUTION: 

CAUTION: 

CAUTION: DO NOT

connect this brewer to
hot water. The inlet

valve is not rated for hot water.

IMPOR

IMPOR

IMPOR

IMPOR

IMPORTTTTTANT

ANT

ANT

ANT

ANT:::::     This

equipment is to be
installed to comply with

the applicable federal, state, or
local plumbing and electrical
codes having jurisdiction.

This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.

• 

Do NOT immerse the unit in water or any other liquid

• 

To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be

done only by authorized service personnel.

• 

Keep hands and other items away from hot parts of unit during operation.

• 

Never clean with scouring powders, bleach or harsh implements.

Conventions

Conventions

Conventions

Conventions

Conventions

W

W

W

W

WARNINGS – 

ARNINGS – 

ARNINGS – 

ARNINGS – 

ARNINGS – TTTTTo help a

o help a

o help a

o help a

o help avoid personal injur

void personal injur

void personal injur

void personal injur

void personal injuryyyyy

Important Notes/Cautions – from the factory

Important Notes/Cautions – from the factory

Important Notes/Cautions – from the factory

Important Notes/Cautions – from the factory

Important Notes/Cautions – from the factory

Sanitation Requirements

Sanitation Requirements

Sanitation Requirements

Sanitation Requirements

Sanitation Requirements

1

2

3

4

FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM

Summary of Contents for TLP10

Page 1: ... the correct volume the heating elements will energize automatically With ADS Systems there is no danger of element burnout caused by an empty tank 4 Turn on the control panel by pressing the ON OFF button 5 The heating tank will require 20 to 30 minutes to reach operating temperature 200 F as indicated by the READY TO BREW indicator 6 Prior to brewing dispense 12 ounces of hot water through the h...

Page 2: ... these steps Before changing the brew volume wait until unit reaches brew temperature Ready to Brew light comes on insert the brewcone into place on the brewer then place a measuring container centered beneath the brewcone Brew Volume Factory Pre set Full Brew to 2 2 Liters ENTER THE PROGRAMMING MODE 1 Be sure to have brewcone airpot in position Press and HOLD until hot water starts running from s...

Page 3: ...C 860 VALVE LIQUID DISPENSING LEFT 220VAC 12W MODEL 30 14 WC 5227 COMPOUND SILICONE 5 OZ TUBE 15 WC 3503 LEG SCREW BUMPER 3 8 16 STUD 16 WC 102 SWITCH TOGGLE SPST 25A 250VAC RESISTIVE Models 10 20 16A WC 103 SWITCH TOGGLE DPST 25A 125 250 VAC RESISTIVE Models 15 30 61 17 WC 826 VALVE INLET 1 15 GPM 120V 10W Models 10 20 15 61 17A WC 856 VALVE INLET 1 15 GPM 240V 10W Model 30 18 WC 54107 TANK COMPL...

Page 4: ...d by a professional certified technician and must comply with all local electrical mechanical and plumbing codes 3 Wilbur Curtis Company will not be responsible for the operation of equipment at other than the stated voltages on the serial plate 4 Abuse or neglect including failure to periodically clean or remove lime accumulations Manufacturer is not responsible for variation in equipment operati...

Reviews: