OHTAKE OM-26RB Series, Руководство по эксплуатации

Страница: 8 / 24

－
7
－
５．
ADJUSTMENTS AND CHECKS BEFORE USE
５－１．
Checking the model number of the main body
Check if the machine has the parts which match the nominal diameter of the
screws to be loaded. Check the model number of the rail, escaper, robot es-
caper guide, and passing plate by referring to the following table.
Before delivery, each section of the machine is checked and adjusted with
panhead screws matching the nominal diameters of the model ordered.
Operate the machine with the screws loaded to check that the pick up is
smooth. If the height or or shape of the screw head is different or if the
operation is regarded as abnormal, each section must be readjusted.
If this is the case, make the following checks and adjustments:
Identification stamp
Escaper
Robot escaper
guide
If the rail, escaper, robot escaper guide and passing plate are replaced, screws with a different nominal diameter
can be accepted. After these parts are replaced, fine adjusting is required.
The respective adjusting procedures will be described elsewhere. Please read these procedures.
Passing plate
identification seal
The rail identification
seal can be located after
removing the front cover.
Screw pick up site
Reference table of the specified screws
Screw
feeder
series
Screw
feeder
model
Screw
size
Exchange kit
No.
Rail model
No.
Escaper
model No.
Robot
escaper guide2
model No.
Passing
plate
model No.
Screw
size
Screw
shaft
diameter
（
φ
）
Screw
head
diameter
（
φ
）
Washer
diameter
（
φ
）
Screw
head
thickness
（mm）
Screw shaft
length（mm）
Sems
Double
sems
Washer
head
OM-26RB20
φ
2.0 OMR20SET2 OMR20 SIE20
φ
2.0 1.9～2.1 2.4～6 2.4～10 0.35～6 2.6～25 ○ ○ ○ ○ ○ ○
OM-26RB23
φ
2.3 OMR23SET2 OMR23 SIE23
φ
2.3 2.2～2.4 2.7～6 2.7～10 0.35～6 2.9～25 ○ ○ ○ ○ ○ ○
OM-26RB26
φ
2.6 OMR26SET2 OMR26 SIE26
φ
2.6 2.5～2.7 3.0～6 3.0～10 0.35～6 3.2～25 ○ ○ ○ ○ ○ ○
OM-26RB30
φ
3.0 OMR30SET2 OMR30 SIE30
φ
3.0 2.9～3.2 3.5～6 3.5～11 0.35～6 3.6～25 ○ ○ ○ ○ ○ ○
OM-26RB35
φ
3.5 OMR35SET2 OMR35 SIE35
φ
3.5 3.4～3.7 4.0～8 4.0～11 0.35～6.5 4.1～25 ○ ○ ○ ○ ○ ○
OM-26RB40
φ
4.0 OMR40SET2 OMR40 SIE40
φ
4.0 3.8～4.2 4.5～8 4.5～12 0.35～6.5 4.6～25 ○ ○ ○ ○ ○ ○
OM-26RB50
φ
5.0 OMR50SET2 OMR50 SIE50 OM50
φ
5.0 4.8～5.2 5.5～10 5.5～12 0.35～7 5.6～25 ○ ○ ○ ○ ○ ○
OM-26RB60
φ
6.0 OMR60SET2 OMR60 SIE60 OM60
φ
6.0 5.8～6.2 6.5～11 6.5～12 0.35～7.5 6.6～25 ○ ○ ○ ○ ○ ○
使用ネジ
の呼び
ピッチ 外形min NJ0.5
2 0.4 0.095 1.91 NSB0.35
2.3 0.4 0.095 2.21
2.6 0.45 0.1 2.50
3 0.5 0.106 2.89
3.5 0.6 0.125 3.38
4 0.7 0.14 3.86
5 0.8 0.15 4.85
6 1 0.18 5.82
OM-26RB
SIE2R20-30 OM20-30
SIE2R35-40 OM35-40
SIE2R50-60
Shape of screw head
Pan head
bind
Flat
head
hexagon
flange
bolt
○ Check the screw load amount
○ Check and adjust the passing plate
○ Check and adjust the holding plate
○ Check and adjust the timer
○ Check and adjust the brush
○ Check and adjust the rail vibration
○ Check and adjust the front and rear sides of the rail