OHAUS Defender i-DT61PW, Инструкция по эксплуатации

Страница: 48 / 68

EN-46 Defender 6000 Indicators
4.9 Discrete I/O (for i-DT61XWE model)
Discrete I/O menu allows the configuration of 3 inputs and 4 outputs. The Discrete Input0 is located at J16 on
the mainboard (please refer to the Mainboard section for where it is located), while other Discrete Inputs &
Outputs are located at the Discrete I/O optional board.
Menu Sub-Menu
Sub-Menu
(in segment) Options
Options ( in segment)
I.O.
I.O.
Reset
reset
no , yes NO , YES
TYPE tYPE OPEN , CLOSED OPEN , CLOSED
Discrete Input0
INPUt0
Off , Zero, Tare, Clear Tare,
Print, Unit, Accumulate, Start,
Reset, Start/Stop,
Pause/Resume
OFF , ZErO , tArE , CLr.tAr ,
PrINt , UNIt , ACCUmM , StArt
rESEt , StA-SP , PA-rE
Discrete Input1
INPUt1
Off , Zero, Tare, Clear Tare,
Print, Unit, Accumulate, Start,
Reset, Start/Stop,
Pause/Resume
OFF , ZErO , tArE , CLr.tAr ,
PrINt , UNIt , ACCUmM , StArt
rESEt
,
StA-SP
,
PA-rE
Discrete Input2
INPUt2
Off , Zero, Tare, Clear Tare,
Print, Unit, Accumulate, Start,
Reset, Start/Stop,
Pause/Resume
OFF , ZErO , tArE , CLr.tAr ,
PrINt , UNIt , ACCUmM , StArt
rESEt , StA-SP , PA-rE
Discrete
Output1
OUt1
Off
, Overload, Underload,
Over, Under, Accept,
Under/Over, SP1, SP2, SP3,
SP4, Alarm
OFF , OU.LOAD , UN.LOAD , over ,
UNDEr , ACCEPt , UN-OU ,
F.SP1 , F.SP2 , F.SP3 , F.SP4 ,
ALArmM
Discrete
Output2
OUt2
Off , Overload, Underload,
Over, Under, Accept,
Under/Over, SP1, SP2, SP3,
SP4, Alarm
OFF , OU.LOAD , UN.LOAD , over ,
UNDEr , ACCEPt , UN-OU , F.SP1 ,
F.SP2 , F.SP3 , F.SP5 , ALArmM
Discrete
Output3
OUt3
Off , Overload, Underload,
Over, Under, Accept,
Under/Over, SP1, SP2, SP3,
SP4, Alarm
OFF , OU.LOAD , UN.LOAD , over ,
UNDEr , ACCEPt , UN-OU , F.SP1 ,
F.SP2 , F.SP3 , F.SP5 , ALArmM
Discrete
Output4
OUt4
Off
, Overload, Underload,
Over, Under, Accept,
Under/Over, SP1, SP2, SP3,
SP4, Alarm
OFF , OU.LOAD , UN.LOAD , over ,
UNDEr , ACCEPt , UN-OU , F.SP1 ,
F.SP2 , F.SP3 , F.SP5 , ALArmM
End
End
\
/
4.9.1 I/O Type
Set the status of the relay output.
OPEN
= the initial state of the relay output is normally open.
CLOSED
= the initial state of the relay output is normally closed.