manualshive.com logo in svg

OfiTE 900, Инструкция по эксплуатации, Страница: 44 / 58

Поделиться
Скачать
OfiTE 900 Скачать руководство пользователя страница 44

Patent No. 6,766,028 - OFI Testing Equipment, Inc.

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

43

19. Place the bearing guide back into the body and secure it in place with the 

three standoffs.

20. Reattach the encoder board to the bearing guide.

21. Carefully place the spring mounting plate onto the three standoffs.  

Secure it in place with the three hex screws.

 

Be careful not to bend the torsion spring.

22. Locate the notch on the transducer body.  Turn the transducer 

counterclockwise all the way against the stop.  Adjust the position of the 

notch on the transducer so that it rests on the far right edge of the black 

mark on the encoder board.

23. Tighten the set screw on the zero calibration knob.  This will lock the 

spring in place.

24. Test the transducer to make sure it turns freely and returns to the 

designated resting place.

25. Place the housing cover back onto the unit and secure it in place with the 

five screws.

26. Adjust the P value (see page 49 for instructions).  Then recalibrate the 

viscometer (see page 14).

Содержание 900



























































Отзывы:

Нет отзывов