OCHIAI DP-10 Скачать руководство пользователя страница 19

Страница: 19 / 24

English

ASSEMBLY AND PREPARATION

Location of Parts and Labels

A. Cutting Blade

B. Gear Case

C. Blade Angle Fixing Knob

Blade Cover

E. Warning Label

F. Warning Label

G. Frame Serial Number Label

H. Owner’s Manual

I. MDC Sheet

E. Warning Label

(a) WARNING

(b) Wear head, eye and ear protectors.

(d) Cutter blades can cause severe injury.

F. Warning Label

(a) Sound Level

(b) Arrow to represent idea of keeping safe distance away from

hazard. Keep bystanders at least 15m away.

Frame Serial Number

The frame serial number (G) is the only means of identifying

your particular products from others of the same model type.

The frame serial number is needed by your dealer when

ordering parts.

Assembly

DANGER

Blade angle change will be performed under the

following conditions.

●

Stop the engine.

●

Fit the cover to the cutting blade.

●

Loosen the blade angle

fastening knob (A).

(Turn the knob

counterclockwise to rotate

about 2 times).

●

Push the blade angle holding

lever (B) and choose desired

blade angle using the blade

turning lever.

●

Firmly retighten the blade angle

fastening knob.

A. Blade angle fastening

knob

Blade angle holding lever

Blade angle turning lever

Screw: 2.5 N·m

Screw: 3.5 N·m

Содержание DP-10

























Результаты поиска

Содержание DP-10

Отзывы:

Похожие инструкции для DP-10

Бренды по названию

Популярные бренды

OCHIAI DP-10, Руководство пользователя

Результаты поиска

Содержание DP-10

Отзывы:

Похожие инструкции для DP-10

Бренды по названию

Популярные бренды