manualshive.com logo in svg

Oce TCS500, Руководство пользователя, Страница: 98 / 306

Поделиться
Скачать
Oce TCS500 Скачать руководство пользователя страница 98

98

Chapter 4 Use the PLC applications to control your workflow

The user interface of the Océ Queue Manager

The status bar

The status bar at the bottom of the Océ Queue Manager displays the following.

■

The system status (connected or disconnected).

■

The system name ('Localhost' if you work on the Océ Power Logic

®

 controller).

■

The job status (for example 'Printing').

■

The user mode ('Key Operator', 'Repro Operator', 'System Administrator', 
'Service Operator' or 'Anonymous').

The window for the print queue 

The print queue window in the left-hand pane contains two sections.

■

The top section above the separation line shows the job that is printed.

■

The bottom section under the separation line shows the jobs that wait to be 
printed. The window displays the jobs in the order in which the jobs are received.

The window for the inbox queue or history queue

The inbox queue in the right-hand pane contains the jobs that were sent to the inbox 
on the controller. You can print the jobs, delete the jobs and view the properties of 
the jobs. The print jobs are sent to the inbox when the setting Key Operator - 
System - Job management - Print jobs in the Océ Settings Editor is set to inbox or 
when 'Send to inbox' is enabled in the driver.

The history queue in the right-hand pane contains the jobs that have been printed. 
You can print the jobs, delete the jobs and view the properties of the jobs. Use the 
setting Key Operator - System - Job management - History queue - Print job 
lifetime in the Océ Settings Editor to define how long the jobs must remain in the 
history queue.

Содержание TCS500



















































































































































































































































































































Отзывы:

Нет отзывов