O.S. engine MAX FXi 46 Скачать руководство пользователя | Manualshive

Страница: 8 / 28

background image

Installation in the Model

Make sure that the mounting beams are
parallel and that their top surfaces are in the
same plane.

•

Before connecting the throttle-
lever/servo linkage, make sure that no
part of the linkage interferes with the
internal structure of the aircraft or
wiring, etc., when the throttle is fully
open or fully closed.

•

Set the throttle lever linkage so that the
throttle rotor is (a) fully open when the
transmitter throttle stick is fully
advanced and (b) fully closed when the

THROTTLE LINKAGE

INSTALLATION OF THE ENGINE

BASIC ENGINE PARTS

8

«
...
6
7
8
9
10
...
»

Содержание MAX FXi 46





























Отзывы:

Нет отзывов

Похожие инструкции для MAX FXi 46

Бренд: JetCat Страницы: 74

Бренд: Westerbeke Страницы: 60

Бренд: Graco Страницы: 26

Бренд: Oriental motor Страницы: 8

403F-E17T 404F-E22T

Бренд: Perkins Страницы: 108

Бренд: LAMBERT Страницы: 24

Бренд: MJ Research Страницы: 143

Бренд: Hoval Страницы: 12

Бренд: Honda Страницы: 139

Бренд: Honda Страницы: 64

Бренд: Honda Страницы: 84

dunkermotoren D258

Бренд: Ametek Страницы: 8

Бренд: Jets Munt Страницы: 23

Бренд: Louvolite Страницы: 2

Para-RC Cloud 0.5 ARF

Бренд: Hacker Страницы: 6

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

TWINMOT T2-PLUS H

Бренд: Germany Motions Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды